- 您現在的位置：買賣IC網 > PDF目錄189008 > NE5560 (NXP Semiconductors N.V.) Switched-mode power supply control circuit PDF資料下載
參數資料
| 型號： | NE5560 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Switched-mode power supply control circuit |
| 中文描述： | 開關電源控制電路 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 240K |
| 代理商： | NE5560 |
Philips Semiconductors
Product specification
NE/SE5560
Switched-mode power supply control circuit
1994 Aug 31
13
δ INCREASES
V6
V15
SET
RESET
CHARGE
.6V
5.6V
SAWTOOTH
1.1V
DISCHARGE
DEAD
TIME
SL00376
Figure 17. Start-Stop Circuit
Remote On/Off Circuit (Pin 10)
In systems where two or more power supplies are used, it is often
necessary to switch these supplies on and off in a sequential way.
Furthermore, there are many applications in which a supply must be
switched by a logical signal. This can be done via the
TTL-compatible remote on/off input on Pin 10. The output pulse is
inhibited for levels below 0.8V. The output of the IC is no longer
blocked when the remote on/off input is left floating or when a
voltage >2V is applied. Start-up occurs via the slow-start circuit.
The Output Stage
The output stage of the NE5560 contains a flip-flop, a push-pull
driven output transistor, and a gate, as indicated in Figure 18. The
flip-flop is set by the flyback of the sawtooth. Resetting occurs by a
signal either from the PWM or the current limit circuit. With this
configuration, it is assured that the output is switched only once per
period, thus prohibiting double pulsing. The collector and emitter of
the output transistor are connected to respectively Pin 15 and Pin
14, allowing for normal or inverted output pulses. An
internally-grounded emitter would cause intolerable voltage spikes
over the bonding wire, especially at high output currents.
This current capability of the output transistor is 40mA peak for VCE
0.4V. An internal clamping diode to the supply voltage protects the
collector against overvoltages. The max. voltage at the emitter (Pin
14) must not exceed +5V. A gate, activated by one of the set or
reset pulses, or by a command from the start-stop circuit will
immediately switch-off the output transistor by short-circuiting its
base. The external inhibitor (Pin 13) operates also via this base.
Demagnetization Sense
As indicated in Figure 18, the output of this NPN comparator will
block the output pulse, when a voltage above 0.6V is applied to Pin
13. A specific application for this function is to prevent saturation of
forward-converter transformers. This is indicated in Figure 19.
Feed-Forward (Pin 16)
The basic formula for a forward converter is
V
OUT +
dVIN
n
(n
+ transformer ratio)
This means that in order to keep VOUT at a constant value, the duty
cycle
δ must be made inversely proportional to the input voltage. A
pre-regulation (feed-forward) with the function
δ~1/VIN can ease the
feedback-loop design.
“I” “I” “n”
NOTES:
The signal V13 can be derived from the demagnetizing winding in
a forward converter as shown below.
FLYBACK
SET
RESET
FROM START STOP
0.6V
13
14
15
+
–
VZ
V1
B
H
P1
P2
S1
+
–
SL00377
Figure 18. Output Stage
This loop now only has to regulate for load variations which require
only a low feedback gain in the normal operation area. The
transformer of a forward converter must be designed in such a way
相關PDF資料 |
PDF描述 |
|---|---|
| NE56631-31D | Active-LOW system reset |
| NE57600GD-G | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO6 |
| NES5NAD1-14.3181-20(T) | QUARTZ CRYSTAL RESONATOR, 14.3181 MHz |
| NKS5NEK1-14.7456-10(T) | QUARTZ CRYSTAL RESONATOR, 14.7456 MHz |
| NKS5NEK1-19.4400-10(T) | QUARTZ CRYSTAL RESONATOR, 19.44 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NE5560D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PACKAGE INFORMATION |
| NE5560F | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LINEAR INTEGRATED CIRCUITS |
| NE5560N | 制造商: 功能描述: 制造商:undefined 功能描述: |
| NE5561 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Switched-mode power supply control circuit |
| NE556-1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual timer |
發布緊急采購，3分鐘左右您將得到回復。