參數資料
型號: NE12S0A0V06PNFA
廠商: Delta Electronics, Inc.
英文描述: Delphi NE Series Non-Isolated Point of Load DC/DC Modules: 3.0~13.8Vin, 0.59V-5.1Vout, 6Aout
中文描述: 德爾福NE系列非隔離負載的DC / DC模塊:3.0點?13.8Vin,0.59V - 5.1Vout,6Aout
文件頁數: 6/12頁
文件大小: 495K
代理商: NE12S0A0V06PNFA
12S06A_02012007
DS_NE
6
FEATURES DESCRIPTIONS
Enable (On/Off)
The ENABLE (on/off) input allows external circuitry to put
the NE converter into a low power dissipation (sleep)
mode. Positive ENABLE is available as standard. With
the active high function, the output is guaranteed to turn
on if the ENABLE pin is driven above
0.8V. The output will
turn off if the ENABLE pin voltage is pulled below 0.3V.
Undervoltage Lockout
The ENABLE pin is also used as input UVLO function.
Leaving the enable floating, the module will turn on if the
input voltage is higher than the turn-on threshold and turn
off if the input voltage is lower than the turn-off threshold.
The d
efault turn-on voltage is 3.1V with 300mV
hysteresis.
The turn-on voltage may be adjusted with a resistor
placed between the “Enable” pin and “Ground” pin. The
equation for calculating the value of this resistor is:
(
34
.
×
R
V
V
V
RTH
EN
FTH
EN
3
_
_
=
Enable
)
8
34
.
05
.
15
_
+
+
×
=
R
V
RTH
EN
NE10A/6A
R
Fig. 18
. UVLO setting
V
_
is the turn-off threshold
V
_
is the turn-on threshold
R (Kohm) is the outen resistor connected from Enable pin
to the GND
An active high voltage will disable the input UVLO
function.
FTH
EN
RTH
EN
DESIGN CONSIDERATIONS
The NE06 uses a single phase and voltage mode
controlled buck topology. The output can be trimmed from
0.59Vdc to 5.1Vdc by a resistor from Trim pin to Ground.
The converter can be turned ON/OFF by remote control
with positive on/off (ENABLE pin) logic. The converter DC
output is disabled when
the signal is driven low (below
0.3V). This pin is also used as the input turn on threshold
judgment. Its voltage is percent of Input voltage during
floating due to internal connection. So we do not suggest
using an active high signal (higher than 0.8V) to turn on
the module because this high level voltage will disable
UVLO function. The module will turn on when this pin is
floating and the input voltage is higher than the threshold.
The converter can protect itself by entering hiccup mode
against over current and short circuit condition. Also, the
converter will shut down when an over voltage protection
is detected.
Safety Considerations
It is recommended that the user to provide a very
fast-acting type fuse in the input line for safety. The output
voltage set-point and the output current in the application
could define the amperage rating of the fuse.
相關PDF資料
PDF描述
NE12S0A0H10PNFA Delphi NE Series Non-Isolated Point of Load DC/DC Modules: 3.0~13.8Vin, 0.59V-5.1Vout, 10Aout
NE12S0A0V10PNFA Delphi NE Series Non-Isolated Point of Load DC/DC Modules: 3.0~13.8Vin, 0.59V-5.1Vout, 10Aout
NE2001-VA20 Near edge thermal printhead (8 dots / mm)
NE2001-VA20A Near edge thermal printhead (8 dots / mm)
NE23300 SUPER LOW NOISE HJ FET (SPACE QUALIFIED)
相關代理商/技術參數
參數描述
NE12S0A0V06PNFA_08 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Delphi NE Series Non-Isolated Point of Load DC/DC Modules:3.1~13.8Vin, 0.59V-5.1Vout, 6Aout
NE12S0A0V06PNFA_09 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Delphi NE Series Non-Isolated Point of Load DC/DC Modules: 3.1~13.8Vin, 0.59V-5.1Vout, 6Aout
NE12S0A0V10PKFA 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Delphi NE Series Non-Isolated Point of Load DC/DC Modules: 3.0~13.8Vin, 0.59V-5.1Vout, 10Aout
NE12S0A0V10PKFC 制造商:DELTA 制造商全稱:Delta Electronics, Inc. 功能描述:Delphi NE Series Non-Isolated Point of Load DC/DC Modules: 3.0~13.8Vin, 0.59V-5.1Vout, 10Aout
NE12S0A0V10PNFA 功能描述:POWER MODULE POL 10A RoHS:是 類別:電源 - 板載 >> DC DC Converters 系列:Delphi NE 標準包裝:250 系列:*