- 您現在的位置：買賣IC網 > PDF目錄1957 > NCV7341D20G (ON Semiconductor)TXRX CAN 12/24V HS LP 14-SOIC PDF資料下載
參數資料
| 型號： | NCV7341D20G |
| 廠商： | ON Semiconductor |
| 文件頁數： | 16/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | TXRX CAN 12/24V HS LP 14-SOIC |
| 標準包裝： | 55 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | CAN |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁
NCV7341
http://onsemi.com
7
Table 3. OPERATION MODES
Conditions
Transceiver Behavior
Pin STB
Pin EN
VCC/VIO
Undervoltage
Flag
VBAT
Undervoltage
Flag
Powerup or
Wakeup Flag
Operating Mode
Pin INH
X
Set
X
Sleep
Floating
Reset
Set
Standby
High
Reset
If in sleep, then no change
Floating
otherwise standby
High
Low
Reset
Set
Standby
High
Reset
If in sleep, then no change
Floating
otherwise standby
High
Low
High
Reset
Set
Standby
High
Reset
If in sleep, then no change
Floating
otherwise gotosleep
High
Low
Reset
X
Receiveonly
High
Reset
X
Normal
High
Normal Mode
In Normal mode, the transceiver is able to communicate
via the bus lines. The CAN controller can transmit data to the
bus via TxD pin and receive data from the bus via Pin RxD.
The bus lines (CANH and CANL) are internally biased to
VCC/2 via the commonmode input resistance. Pin VSPLIT
is also providing voltage VCC/2 which can be further used
to externally stabilize the common mode voltage of the bus
– see Figure 2 and Figure 3. Pin INH is active (pulled high)
so that the external regulators controlled by INH Pin are
switched on.
ReceiveOnly Mode
In Receiveonly mode, the CAN transmitter is disabled.
The CAN controller can still receive data from the bus via
RxD Pin as the receiver part remains active. Equally to
normal mode, the bus lines (CANH and CANL) are
internally biased to VCC/2 and Pin VSPLIT is providing
voltage VCC/2. Pin INH is also active (pulled high).
Standby Mode
Standby mode is a lowpower mode. Both the transmitter
and the receiver are disabled and a very lowpower
differential receiver monitors the CAN bus activity. Bus
lines are biased internally to ground via the common mode
input resistance and Pin VSPLIT is highimpedant (floating).
A wakeup event can be detected either on the CAN bus or
on the WAKE Pin. A valid wakeup is signaled on pins ERR
and RxD. Pin INH remains active (pulled high) so that the
external regulators controlled by INH Pin are switched on.
GoToSleep Mode
GoToSleep mode is an intermediate state used to put the
transceiver into sleep mode in a controlled way.
GoToSleep mode is entered when the CAN controller
puts pin EN to High and STB Pin to Low. If the logical state
of Pins EN and STB is kept unchanged for minimum period
of th(min) and neither a wakeup nor a powerup event occur
during this time, the transceiver enters sleep mode. While in
gotosleep mode, the transceiver behaves identically to
standby mode.
Sleep Mode
Sleep mode is a lowpower mode in which the
consumption is further reduced compared to standby
mode. Sleep mode can be entered via gotosleep mode or
in case an undervoltage on either VCC or VIO occurs for
longer than the undervoltage detection time. The
transceiver behaves identically to standby mode, but the
INH Pin is deactivated (left floating) and the external
regulators controlled by INH Pin are switched off. In this
way, the VBAT consumption is reduced to a minimum. The
device will leave sleep mode either by a wakeup event (in
case of a CAN bus wakeup or via Pin WAKE) or by putting
Pin STB high (as long as an undervoltage on VCC or VIO
is not detected).
Internal Flags
The transceiver keeps several internal flags reflecting
conditions and events encountered during its operation.
Some flags influence the operation mode of the transceiver
TxD dominant timeout flags, all others can be read by the
CAN controller on Pin ERR. Pin ERR signals internal flags
depending on the operation mode of the transceiver. An
overview of the flags and their visibility on Pin ERR is given
in Table 4. Because the ERR Pin uses negative logic, it will
be pulled low if the signaled flag is set and will be pulled
high if the signaled flag is reset.
相關PDF資料 |
PDF描述 |
|---|---|
| NCV7356D2R2 | IC TXRX CAN SGL WIRE 14-SOIC |
| NCV7380DR2G | IC TRANSCEIVER LINEAR 8-SOIC |
| NCV7382DR2G | IC TRANSCEIVER LIN ENH 8-SOIC |
| NCV7441D20G | IC TXRX CAN DUAL HS LP 14-SOIC |
| NET+40-QIVRO-4 | IC MPU 32B 33MHZ LINUX 208PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCV7341D20R2G | 功能描述:CAN 接口集成電路 IMPR. HS LP CAN TRANSC. + RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| NCV7341D21G | 功能描述:網絡控制器與處理器 IC HS LP CAN TRANSC. RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| NCV7341D21R2G | 功能描述:網絡控制器與處理器 IC HS LP CAN TRANSC. RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| NCV7342 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Speed Low Power CAN Transceiver |
| NCV7342D10R2G | 制造商:ON Semiconductor 功能描述:HS LP CAN TRANSC (L-WU) - Tape and Reel 制造商:ON Semiconductor 功能描述:IC TXRX CAN SGL WIRE 制造商:ON Semiconductor 功能描述:REEL - HS LP CAN TRANSC (L-WU) |
發布緊急采購，3分鐘左右您將得到回復。