參數資料
型號： NCP5331FTR2
廠商： ON SEMICONDUCTOR
元件分類： 穩壓器
英文描述： Two-Phase PWM Controller with Integrated Gate Drivers
中文描述： 1.5 A SWITCHING CONTROLLER, 750 kHz SWITCHING FREQ-MAX, PQFP32
封裝： LQFP-32
文件頁數： 17/38頁
文件大?。?/td> 424K
代理商： NCP5331FTR2
NCP5331
http://onsemi.com
17
Figure 17. Inductive Sensing Waveform During a
Load Step with Fast RC Time Constant (50
μ
s/div)
Figure 18. Hiccup Mode Operation
Figure 19. Overcurrent Timer Operation
The waveforms in Figure 17 show a simulation of the
current sense signal and the actual inductor current during
a positive step in load current with values of L = 500 nH,
R
L
= 1.6 m
, RSx = 20 k and CSx = 0.01
μ
F. For ideal current
signal compensation the value of RSx should be 31 k
. Due
to the faster than ideal RC time constant there is an overshoot
of 50% and the overshoot decays with a 200
μ
s time
constant. With this compensation the I
LIM
pin threshold
must be set more than 50% above the full load current to
avoid triggering hiccup mode during a large output load
step.
Current Limit, Hiccup Mode and Overcurrent Timer
The individual phase currents are summed and low-pass
filtered to create an average current signal. The average
current is then compared to a user adjustable voltage at the
I
LIM
pin. If the I
LIM
voltage is exceeded, the fault latch is set,
switching stops, and the COMP pin is discharged until it
decreases to 0.27 V. At this point, the fault latch is reset, the
COMP voltage will begin to rise and a new startup cycle
begins. During startup, the output voltage and load current
will increase until either regulation is achieved or the I
LIM
voltage is again exceeded. The converter will continue to
operate in “hiccup mode” until the fault condition is
corrected or the overcurrent timer expires.
When an overcurrent fault occurs the converter will enter
a low duty cycle hiccup mode. During hiccup mode the
converter will not switch from the time a fault is detected
until the soft start capacitor (C
C2
) has discharged below the
COMP Discharge Threshold and then charged back up
above the Channel Start Up Offset. Figure 18 shows the
NCP5331 operating in hiccup mode with the converter
output shorted to GND. Hiccup mode will continue until the
overcurrent timer terminates operation.
The overcurrent timer sets a limit to how long the
converter will operate in hiccup mode. Placing a capacitor
from the C
OVC
pin to GND sets the length of time - a larger
capacitor sets a longer time. The first hiccup pulse starts the
timer by turning on a current source that charges the
capacitor at the C
OVC
pin. If the voltage at the C
OVC
pin rises
to 3 V before the output voltage exceeds the PGD threshold,
then the overcurrent latch is set, COMP is discharged, and
PGD is latched Low. Once set, the overcurrent latch will
hold the converter in this state until the input voltage, either
V
CCL
or V
CCH
, is cycled. Conversely, if the timer starts and
either the output short circuit is removed or the load is
decreased before the overcurrent timer expires, PGD will
transition High after its programmed delay time and the
timer will be reset. The nominal overcurrent time can be
calculated using the following equation.
tOVC
COVC
(OVCTHRESH
OVCMIN) IOVC
COVC
COVC
(3.0 V
0.25 V) 5.0 A
105
5.5
Figure 19 shows the overcurrent timer terminating hiccup
mode when C
OVC
charges up to 3.0 V.
相關PDF資料
PDF描述
NCP5383 Two Phase Buck Controller with Integrated Gate Drivers and AVP
NCP5422ADR2G Dual Out−of−Phase Synchronous Buck Controller with Current Limit
NCP5423 Dual Out−of−Phase Synchronous Buck Controller with Current Limit
NCP5423DR2G Dual Out−of−Phase Synchronous Buck Controller with Current Limit
NCP5424DG Dual Synchronous Buck Controller with Input Current Sharing
相關代理商/技術參數
參數描述
NCP5331FTR2G 功能描述:DC/DC 開關控制器 2 Phase Buck w/Gate Drivers for Athlon RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
NCP5332A 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two-Phase Buck Controller with Integrated Gate Drivers and 5-Bit DAC
NCP5332A/D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two-Phase Buck Controller with Integrated Gate Drivers and 5-Bit DAC
NCP5332ADW 功能描述:DC/DC 開關控制器 2 Phase Buck w/Gate RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
NCP5332ADWR2 功能描述:DC/DC 開關控制器 2 Phase Buck w/Gate RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*