參數資料
型號： NCP5318FTR2G
廠商： ON SEMICONDUCTOR
元件分類： 穩壓器
英文描述： Two/Three/Four−Phase Buck CPU Controller
中文描述： SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQFP32
封裝： LEAD FREE, LQFP-32
文件頁數： 17/31頁
文件大?。?/td> 384K
代理商： NCP5318FTR2G
NCP5318
http://onsemi.com
17
Inductive Current Sensing
For lossless sensing, current can be measured across the
inductor as shown in Figure 19. In the diagram, L is the
output inductance and R
L
is the inherent inductor resistance.
To compensate the current sense signal, the values of R
CSx
and C
CSx
are chosen so that L/R
L
= R
CSx
x C
CSx
. If this
criteria is met, the current sense signal should be the same
shape as the inductor current and the voltage signal between
CSxP and CSxN will represent the instantaneous value of
inductor current. Also, the circuit can be analyzed as if a
sense resistor of value R
L
was used. When choosing or
designing inductors for use with inductive sensing,
tolerances and temperature effects should be considered.
Cores with a low permeability material or a large gap will
usually have minimal inductance change with temperature
and load. Copper magnet wire has a temperature coefficient
of 0.39% per degree C. The increase in winding resistance
at higher temperatures should be considered when setting
the phase peak current limit threshold. If current sensing
more accurate than provided by inductive sensing is
required, current can be sensed through a resistor as shown
in Figure 17.
Current Sharing Accuracy
For accurate current sharing, the current sense inputs
should sense the current at identical points at each phase
sense resistance. Printed Circuit Board (PCB) traces that
carry inductor current can be used as part of the current sense
resistance by selecting where the current sense signal is
picked up along a current carrying trace, but variations of
PCB copper base thickness, plating, and etching can degrade
current sharing and must be well controlled. The total
current sense resistance used for calculations must include
any PCB trace resistance that carries inductor current
between the CSxP input and the CSxN input. Current Sense
Amplifier (CSA) input mismatch and the value of the
current sense component will determine the accuracy of the
current sharing between phases. The worst case CSA input
mismatch is
±
4 mV and will typically be within 1.5 mV. The
difference in peak currents between phases will be the CSA
input mismatch divided by the current sense resistance. If all
current sense components are of equal resistance, a
1.5 mV mismatch with a 1.0 m sense resistance will
contribute 1.5 A of current difference between phases.
Figure 19. Enhanced V
2
Control Employing Lossless Inductive Current Sensing and Internal Ramp
+
CSA
SWNODE
Lx
R
CSx
RLx
CSxP
COx
CSxN
+
V
OUT
(V
CORE
)
“Fast
Feedback”
Connection
+
PWM
COMP
To PWM
Latch Reset
Channel
Startup
Offset
+
E.A.
DAC
Out
V
FB
COMP
Internal Ramp
+
x = 1, 2, 3 or 4
C
CSx
+
V
FFB
External Ramp Size and Current Sensing
The internal ramp allows flexibility in setting the current
sense time constant. Typically, the current sense R
CSx
x
C
CSx
time constant should be equal to or slightly slower than
the inductor’s time constant. If RC is chosen to be smaller
(faster) than L/R
L
, the AC or transient portion of the current
sensing signal will be scaled larger than the DC portion. This
will provide a larger steady
state ramp, but transient circuit
response will be affected and must be evaluated carefully.
The current signal will overshoot during transients and settle
at the rate determined by R
CSx
x C
CSx
. It will eventually
settle to the correct DC level, but the error will decay with
the time constant of R
CSx
x C
CSx
. Excessive error can
degrade transient response, adaptive positioning (droop)
and current limit. During a positive current transient, the
COMP pin will be required to overshoot in response to the
current signal in order to maintain the output voltage. Phase
pulse
by
pulse overcurrent protection will trip earlier than
it would if compensated correctly. Similarly, the V
DRP
signal will overshoot which will produce too much transient
droop in the output voltage, and also result in hiccup
mode
current limit having a lower threshold for fast rising step
loads than for slowly rising output currents.
相關PDF資料
PDF描述
NCP5322ADWG Two−Phase Buck Controller with Integrated Gate Drivers and 5−Bit DAC
NCP5322ADWR2G Two−Phase Buck Controller with Integrated Gate Drivers and 5−Bit DAC
NCP5331FTR2G Two-Phase PWM Controller with Integrated Gate Drivers
NCP5331 Two-Phase PWM Controller with Integrated Gate Drivers
NCP5331FTR2 Two-Phase PWM Controller with Integrated Gate Drivers
相關代理商/技術參數
參數描述
NCP5322A 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two−Phase Buck Controller with Integrated Gate Drivers and 5−Bit DAC
NCP5322A/D 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two-Phase Buck Controller with integrated Gate Drivers and 5-Bit DAC
NCP5322A_07 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two−Phase Buck Controller with Integrated Gate Drivers and 5−Bit DAC
NCP5322ADW 功能描述:DC/DC 開關控制器 2 Phase Buck w/Gate RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
NCP5322ADWG 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Two−Phase Buck Controller with Integrated Gate Drivers and 5−Bit DAC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*