- 您現在的位置：買賣IC網 > Datasheet目錄45 > NCP1083DEG (ON Semiconductor)IC CONV CTLR POE-PD 40W 20-TSSOP Datasheet資料下載
參數資料
| 型號： | NCP1083DEG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 14/18頁 |
| 文件大小： | 257K |
| 描述： | IC CONV CTLR POE-PD 40W 20-TSSOP |
| 標準包裝： | 74 |
| 類型： | 以太網供電開關（PoE） |
| 應用： | 遠程外設（工業控制，相機，數據訪問） |
| 內部開關： | 是 |
| 電流限制： | 1.1A |
| 電源電壓： | 0 V ~ 57 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 |
| 供應商設備封裝： | 20-TSSOP-EP |
| 包裝： | 管件 |
NCP1083
http://onsemi.com
14
When the auxiliary input supply is above 13.5 V, connect
the AUX pin to VPORTN
1,2
. When the auxiliary supply is
below 13.5 V (but above 9 V), calculate the voltage dividers
Raux1, Raux3 and Raux2, Rdet1, Rdet2 to divide the input
voltage using the below formulas together with the formulas
from the previous section. This will ensure that for valid input
voltages, the voltage at the UVLO and AUX pins are above
their threshold voltages. Note that the maximum voltage is
3.3 V.
R
aux3
+
R
aux1
V
t
V
aux
* V
dp
* V
t
R
aux1
+ 20 kW
R
aux2
+
V
aux
* V
dp
* V
d
* V
t
V
t
845
*
V
aux
*V
dp
*V
d
*V
t
24 K
Where V
d
is the voltage drop over the rectifiers and masking
diodes (typical 0.6 V), V
dp
is the forward drop of the
NCP1083 internal diode (typical 0.5 V), and V
t
is the
threshold voltage on the AUX pin (typical 1.5 V).
Note that as soon as the auxiliary supply is connected the
PoE interface (detection and classification) is disabled and
does not allow the PD device to be powered from the
Ethernet until the auxiliary supply is removed.
If the PoE PD device was drawing the current from the
Ethernet cable before the auxiliary supply is connected, the
power will continue to be supplied from the Ethernet cable
unless the voltage of the auxiliary supply is higher than the
Ethernet supply voltage.
Inrush and Operational Current Limitations
The inrush current limit and the operational current limit
are programmed individually by an external Rinrush and
Rilim1 resistors respectively connected between INRUSH
and VPORTN
1,2
, and between ILIM1 and VPORTN
1,2
as
shown in Figure 14.
ILIM1 /
INRUSH
VDDA1
Vbg1
VDDA1
VPORTNx
Ilim_ref
NCP1083
Figure 14. Current Limitation Configuration (Inrush & Ilim1 Pins)
Ilim1
Vds_pgood
threshold
VPORTNx
Pass Switch
Inrush
I_pass_switch
NCP1083
RTN
VDS_PGOOD
0
1
VDDA1
VDDA1
1 V / 9.2 V
2 V
Current_limit_ON
&
detector
Figure 15. Inrush and Ilim1 Selection Mechanism
VDDA1
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1501DMR2G | IC REG SGL BUCK/LINEAR 8MICRO |
| NCP1578MNR2G | IC REG DL BCK/LINEAR SYNC 20-QFN |
| NCP1601BDR2G | IC PFC CTRL CRM/TRANSITION 8SOIC |
| NCP1603D100R2G | IC CTLR PFC/PWM COMBO 16-SOIC |
| NCP1605DR2G | IC PFC CONTROLLER CCM/DCM 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1083DER2G | 功能描述:DC/DC 開關控制器 POE-PD 40W DC-DC AUX SUPP RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| NCP1083QBCGEVB | 功能描述:電源管理IC開發工具 HIGH POWER POE-PD MODULE RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1083WIRGEVB | 功能描述:電源管理IC開發工具 POE-PD MODULE WITH VAUX RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP1086 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
| NCP1086/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1.5 A Adjustable and 3.3 V Fixed Output Linear Regulator |
發布緊急采購，3分鐘左右您將得到回復。