- 您現在的位置：買賣IC網 > PDF目錄383656 > MXB7843EUE (MAXIM INTEGRATED PRODUCTS INC) 2.375V to 5.25V, 4-Wire Touch-Screen PDF資料下載
參數資料
| 型號： | MXB7843EUE |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | 2.375V to 5.25V, 4-Wire Touch-Screen |
| 中文描述： | 2-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO16 |
| 封裝： | 4.40 MM, MO-153AB, TSSOP-16 |
| 文件頁數： | 16/21頁 |
| 文件大?。?/td> | 508K |
| 代理商： | MXB7843EUE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁
M
pointing device presses on the touch screen, the Y+
and Y- drivers are turned on, connecting one side of
the vertical resistive layer to V
DD
and the other side to
ground. In this case, the horizontal resistive layer func-
tions as a sense line. One side of this resistive layer
gets connected to the X+ input, while the other side is
left open or floating. The point where the touch screen
is pressed brings the two resistive layers in contact and
forms a voltage-divider at that point. The data converter
senses the voltage at the point of contact through the
X+ input and digitizes it. The horizontal layer resistance
does not introduce any error in the conversion because
no DC current is drawn.
The conversion process of the analog input voltage to
digital output is controlled through the serial interface
between the A/D converter and the μP. The processor
controls the MXB7843 configuration through a control
byte (Tables 3 and 4). Once the processor instructs the
MXB7843 to initiate a conversion, the MXB7843 biases
the touch screen through the internal switches at the
beginning of the acquisition period. The voltage transient
at the touch screen needs to settle down to a stable volt-
age before the acquisition period is over. After the acqui-
sition period is over, the A/D converter goes into a
conversion period with all internal switches turned off if
the device is in single-ended mode. If the device is in
differential mode, the internal switches remain on from
the start of the acquisition period to the end of the con-
version period.
Power-On Reset
When power is first applied, internal power-on circuitry
resets the MXB7843. Allow 10μs for the first conversion
after the power supplies stabilize. If
CS
is low, the first
logic 1 on DIN is interpreted as a start bit. Until a con-
version takes place, DOUT shifts out zeros.
Power Modes
Save power by placing the converter in one of two low-
current operating modes or in full power-down between
conversions. Select the power-down mode through
PD1 and PD0 of the control byte (Tables 3 and 4).
The software power-down modes take effect after the
conversion is completed. The serial interface remains
active while waiting for a new control byte to start a con-
version and switches to full-power mode. After complet-
ing its conversion, the MXB7843 enters the programmed
power mode until a new control byte is received.
The power-up wait before conversion period is depen-
dent on the power-down state. When exiting software
low-power modes, conversion can start immediately
when running at decreased clock rates. Upon power-
on reset, the MXB7843 is in power-down mode with
PD1 = 0 and PD0 = 0. When exiting software shutdown,
the MXB7843 is ready to perform a conversion in 10μs.
PD1 = 1, PD0 = 1
In this mode, the MXB7843 is always powered. The
device remains fully powered after the current conver-
sion completes.
PD1 = 0, PD0 = 0
In this mode, the MXB7843 powers down after the current
conversion completes or on the next rising edge of
CS
,
whichever occurs first. The next control byte received on
DIN powers up the MXB7843. At the start of a new con-
version, it instantly powers up. When each conversion is
finished, the part enters power-down mode, unless other-
wise indicated. The first conversion after the ADC returns
to full power is valid for differential conversions and sin-
gle-ended measurement conversions.
When operating at full speed and 16 clocks per conver-
sion, the difference in power consumption between
PD1 = 0, PD0 = 1, and PD1 = 0, PD0 = 0 is negligible.
Also, in the case where the conversion rate is
decreased by slowing the frequency of the DCLK input,
the power consumption between these two modes is
not very different. When the DCLK frequency is kept at
2.375V to 5.25V, 4-Wire Touch-Screen
Controller
16
______________________________________________________________________________________
OUTPUT CODE
FS = (V
REF+
- V
REF-
)
FS-3/2LSB
FULL-SCALE
TRANSITION
INPUT VOLTAGE (LSB) = [(V
+IN
) - (V
-IN
)]
1
2
3
FS
0
11
…
111
11
…
110
11
…
101
00
…
011
00
…
010
00
…
001
00
…
000
1LSB =
(V
REF+
- V
REF-
)
4096
Figure 10. Ideal Input Voltages and Output Codes
相關PDF資料 |
PDF描述 |
|---|---|
| MXD1000SE__ | 5-Tap Silicon Delay Line |
| MXD1000PA__ | 5-Tap Silicon Delay Line |
| MXD1000PD__ | 5-Tap Silicon Delay Line |
| MXD1000SA__ | 5-Tap Silicon Delay Line |
| MXD1000UA__ | 5-Tap Silicon Delay Line |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MXB7843EUE+ | 功能描述:觸摸屏轉換器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MXB7843EUE+T | 功能描述:觸摸屏轉換器和控制器 2.375-5.25V 4-Wire Touch-Screen Ctlr RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MXB7843EUE-T | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| MXB7846 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.375V to 5.25V, 4-Wire Touch-Screen Controller with Internal Reference and Temperature Sensor |
| MXB7846EEE | 功能描述:觸摸屏轉換器和控制器 RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
發布緊急采購，3分鐘左右您將得到回復。