參數資料
型號： MX29LV017ATI-70
廠商： Electronic Theatre Controls, Inc.
英文描述： 16M-BIT [2Mx8] CMOS SINGLE VOLTAGE
中文描述： 1,600位[2Mx8] CMOS單電壓
文件頁數： 13/57頁
文件大小： 641K
代理商： MX29LV017ATI-70
13
P/N:PM0901
MX29LV017A
REV. 1.0, NOV. 22, 2002
READING ARRAY DATA
The device is automatically set to reading array data
after device power-up. No commands are required to
retrieve data. The device is also ready to read array data
after completing an Automatic Program or Automatic
Erase algorithm.
After the device accepts an Erase Suspend command,
the device enters the Erase Suspend mode. The sys-
tem can read array data using the standard read tim-
ings, except that if it reads at an address within erase-
suspended sectors, the device outputs status data. After
completing a programming operation in the Erase
Suspend mode, the system may once again read array
data with the same exception. See Erase Suspend/Erase
Resume Commands” for more information on this mode.
The system
must
issue the reset command to re-en-
able the device for reading array data if Q5 goes high, or
while in the "read silicon-ID" and "sector protect verify"
mode. See the "Reset Command" section, next.
RESET COMMAND
Writing the reset command to the device resets the
device to reading array data. Address bits are don't care
for this command.
The reset command may be written between the se-
quence cycles in an erase command sequence before
erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the se-
quence cycles in a program command sequence be-fore
programming begins. This resets the device to reading
array data (also applies to programming in Erase
Suspend mode). Once programming begins, however,
the device ignores reset commands until the operation
is complete.
The reset command may be written between the se-
quence cycles in an Automatic Select command
sequence. Once in the Automatic Select mode, the reset
command
must
be written to return to reading array data
(also applies to Automatic Select during Erase Suspend).
If Q5 goes high during a program or erase operation,
writing the reset command returns the device to read-
ing array data (also applies during Erase Suspend).
Pins
A0
A1
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Code(Hex)
Manufacturer code
VIL
VIL
1
1
0
0
0
0
1
0
C2H
Device code
VIH
VIL
1
1
0
0
1
0
0
0
C8H
Sector Protection
VIL
VIH
0
0
0
0
0
0
0
1
01H (Protected)
Verification
VIL
VIH
0
0
0
0
0
0
0
0
00H(Unprotected)
TABLE 6. SILICON ID CODE
相關PDF資料
PDF描述
MX29LV017ATI-90 16M-BIT [2Mx8] CMOS SINGLE VOLTAGE
MX29LV017AXBC-70 16M-BIT [2Mx8] CMOS SINGLE VOLTAGE
MX29LV017AXBC-90 16M-BIT [2Mx8] CMOS SINGLE VOLTAGE
MX29LV017AXBI-70 16M-BIT [2Mx8] CMOS SINGLE VOLTAGE
MX29LV017AXBI-90 16M-BIT [2Mx8] CMOS SINGLE VOLTAGE
相關代理商/技術參數
參數描述
MX29LV040CQC-55Q 制造商:Macronix International Co Ltd 功能描述:4M (512K X8) 70NS 32PLCC
MX29LV040CQC-70G 制造商:Macronix International Co Ltd 功能描述:MX29LV Series 3 V 4 Mb (512K x 8) 70 ns Parallel Flash - PLCC-32
MX29LV040CQC-90G 制造商:MISCELLANEOUS 功能描述: 制造商:Macronix International Co Ltd 功能描述:IC FLASH 4MBIT 90NS 32PLCC 制造商:Macronix International Co Ltd 功能描述:MX29LV Series 3 V 4 Mb (512K x 8) 90 ns Parallel Flash - PLCC-32
MX29LV040CQI-55Q 制造商:Macronix International Co Ltd 功能描述:IC FLASH 4MBIT 55NS 32PLCC 制造商:Macronix International Co Ltd 功能描述:MX29LV Series 3 V 4 Mb (512K x 8) 55 ns Parallel Flash - PLCC-32
MX29LV040CQI-70G 功能描述:IC FLASH PAR 3V 4MB 70NS 32PLCC RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:MX29LV 標準包裝:1 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:4G（256M x 16） 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:0°C ~ 70°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP I 包裝:Digi-Reel® 其它名稱:557-1461-6
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*