MX-850
SWITCHING CHAR. (cont.)
MIN.
TYP.
MAX.
UNITS
Settling Time, 5k Load
20V step to ±0.1%
20V step to ±0.01%
20V step to ±0.003%
20V step to ±0.001%
Crosstalk
10kHz (20Vp-p)
1MHz (20Vp-p)
10MHz (5Vp-p)
20MHz (3Vp-p)
—
—
—
—
30
50
75
100
35
60
85
120
ns
ns
ns
ns
—
—
—
—
–105
–94
–76
–64
–100
–92
–71
–62
dB
dB
dB
dB
POWER REQUIREMENTS
Power Supply Range
+15V Supply
–15V Supply
+5V Supply
Power Supply Current,
Quiescent
+15V Supply
–15V Supply
+5V Supply
Power Supply Rejection Ratio
Power Supply Dissipation,
Quiescent
+25°C
0 to +70°C
–55 to +125°C
Pd versus Frequency
+14.5
–14.5
+4.75
+15
–15
+5
+15.5
–15.5
+5.25
Volts
Volts
Volts
—
—
—
80
+3
–10
+3
90
+4
–12
+3.5
—
mA
mA
mA
dB
—
—
—
207
—
—
See Figure 4
270
270
280
mW
mW
mW
PHYSICAL/ENVIRONMENTAL
Operating Temp. Range, Case
MX-850MC
MX-850MM
Storage Temperature Range
Package Type
Weight
0
—
—
—
+70
+125
+150
°C
°C
°C
–55
–65
14-pin, metal-sealed, ceramic DIP
0.1 ounces (2.8 grams)
See Figures 3a and 3b.
ABSOLUTE MAXIMUM RATINGS
PARAMETER
LIMITS
UNITS
+15V Supply, Pin 10
–15V Supply, Pin 14
+5V Supply, Pin 12
Digital Inputs, Pins 1, 2, 3
Analog Inputs, Pins 4, 5, 6, 7
Analog Input Current
Lead temperature
(10 seconds)
Switching Frequency/Duty Cycle
–0.5 to +16.5
+0.5 to –16.5
–0.5 to +7
–0.5 to +6
–10.5 to +10.5
±20
300
10/50
Volts
Volts
Volts
Volts
Volts
mA
°C
MHz/%
FUNCTIONAL SPECIFICATIONS
(Apply over the operating temperature range and over the operating power supply
range unless otherwise specified.)
ANALOG INPUTS
MIN.
TYP.
MAX.
UNITS
Analog Signal Range
On Resistance, +25°C
0 to +70°C
–55 to +125°C
R
ON
versus V
IN
Input Leakage Current (Off)
+25°C
0 to +70°C
–55 to +125°C
Output Leakage Current (Off)
+25°C
0 to +70°C
–55 to +125°C
On Channel Leakage Current
+25°C
0 to +70°C
–55 to +125°C
Channel Input Capacitance
Off
On
Channel Output Capacitance
On
Nonlinearity
Large signal bandwidth
(–3dB)
±10
—
—
—
—
18
—
—
See Figure 2
—
90
120
140
Volts
Ohms
Ohms
Ohms
—
—
—
±0.02
—
—
±0.2
±10
±25
nA
nA
nA
—
—
—
±0.02
—
—
±0.2
±20
±40
nA
nA
nA
—
—
—
±0.4
—
—
±1
±25
±35
nA
nA
nA
—
—
4
6
pF
pF
10
12
—
—
80
8
—
100
10
pF
±0.001
—
%FSR
MHz
DIGITAL INPUTS
Logic levels
Logic "1"
Logic "0"
Logic Loading "1"
Logic Loading "0"
+2.0
—
—
—
—
—
—
—
—
+0.8
+10
–10
Volts
Volts
μA
μA
SWITCHING CHARACTERISTICS
Access Time
Break-Before-Make
Delay Time
Enable Delay (On, Off)
Settling Time, 10M Load
10V step to ±0.1%
10V step to ±0.01%
10V step to ±0.003%
10V step to ±0.001%
Settling Time, 5k Load
10V step to ±0.1%
10V step to ±0.01%
10V step to ±0.003%
10V step to ±0.001%
Settling Time, 10M Load
20V step to ±0.1%
20V step to ±0.01%
20V step to ±0.003%
20V step to ±0.001%
—
—
—
—
—
3
20
10
10
ns
ns
ns
—
—
—
—
25
40
60
80
30
50
70
100
ns
ns
ns
ns
—
—
—
—
25
40
60
80
30
50
70
100
ns
ns
ns
ns
—
—
—
—
30
50
75
100
35
60
85
120
ns
ns
ns
ns
TECHNICAL NOTES
1. Proper operation of the MX-850 multiplexer is dependent
upon good board layout and connection practices. Bypass
supplies as shown in the connection diagrams. Mount
bypass capacitors directly to the supply pins whenever
possible.
2. All grounds pins (9, 11, 13) should be tied together and
connected to ground as close to the multiplexer as
possible.
3. When power is off, current limit input signals on pins 4, 5, 6,
and 7 to 20mA. Failure to current limit can cause
permanent damage to the device since, when powering up
or down it is possible that two switches might be on at the
same time. Excessive current (greater than 20mA) will flow
from the more positive input to the more negative input,
permanently damaging the device. Applications in which
the power supply for the multiplexer also powers the signal
sources may not require limiting resistors. See Figure 4.