- 您現在的位置：買賣IC網 > PDF目錄359238 > MULTISYNCFE750 Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A PDF資料下載
參數資料
| 型號： | MULTISYNCFE750 |
| 英文描述： | Monitor_ICs:HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| 中文描述： | Monitor_ICs：HD6433577 LA7841 BA9761F MQ571 XC13289LSP LSC3820P2 uPD61882A |
| 文件頁數： | 52/52頁 |
| 文件大?。?/td> | 517K |
| 代理商： | MULTISYNCFE750 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁
52
MON08 Multilink User Manual
P&E
Microcomputer
Systems, Inc.
MON08 MULTILINK
PROG08SZ software continually records any changes to these security bytes
and stores them in the file SECURITY.INI. The information in this file is also
shared with P&E's In-Circuit Debugger and In-Circuit Simulator Software.
This allows the user to reset the device and still have access to the monitor
mode.
Sometimes the case comes up where the software can’t pass security mode.
The Target Connection and Security Dialog section has a “STATUS” section
which describes the different failures and what to check in each case.
The most common reasons for not passing security are:
- You are not choosing the proper security code to pass security.
- On a power on reset, the device is not powering down to below 0.1
volts. With a Class I board (ICS with processor), you may be driving
the pins on the emulation header while the device is being powered
down. This back-drives current through the ports and doesn’t let the
device fully power down. On other classes of boards, when prompted
to power down the device, the supply voltage might not be dropping
lower than 0.1v which it must to have a power-on reset.
- Make sure the “Target hardware type” is set to the proper class of
hardware.
There are several ways you can specify the proper security bytes:
- If you know the programmed security bytes, i.e. the bytes from
$FFF6-$FFFD, you can enter them in the edit box listed “User:” and
click OK(Retry).
- You can use the “Load from S19” to specify the s-record file which
contains the object information currently programmed into the MCU.
P&E’s software will automatically extract the security information
from this file and use it to pass security. Once you have specified the
s-record file, click the OK(Retry) button.
- You can erase the device. Run the PROG08SZ application, and when the
above box appears, select the “IGNORE security failure…” option and click
OK. Use the Choose Module command to select the appropriate programming
algorithm, and select Erase Module. This should erase the device. You will
have to execute the Choose Module command again before you can access the
blank device. Note: on some older revisions of silicon, you can’t ignore the
security failure, and it will bring this box back up every time you click
OK(Retry). If this is the case, you should obtain the latest silicon revision from
Motorola.
相關PDF資料 |
PDF描述 |
|---|---|
| MUM8128W-17 | x8 EPROM |
| MUM8128W-20 | x8 EPROM |
| MUM8128W-25 | x8 EPROM |
| MUM8128WI-17 | x8 EPROM |
| MUM8128WI-20 | x8 EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MULTI-TC | 制造商:ERSA 功能描述:SOLDERING IRON 230V 75W EURO PLUG 制造商:ERSA 功能描述:SOLDERING IRON, 230V, 75W, EURO PLUG |
| MULTI-TEST | 制造商:L COM 功能描述:PC CABLE TESTER ATA 制造商:L-com Inc 功能描述:PC CABLE TESTER ATA |
| MULTI-USE LIGHT | 制造商:Energizer Battery Company 功能描述: |
| MULTIWATT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT |
| MULTIWATT11 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MULTIWATT |
發布緊急采購，3分鐘左右您將得到回復。