參數資料
型號： MT9126AE
廠商： Mitel Networks Corporation
英文描述： CMOS Quad ADPCM Transcoder
中文描述： 代碼轉換器的CMOS四路差分PcM
文件頁數： 8/22頁
文件大小： 312K
代理商： MT9126AE
MT9126
Preliminary Information
8-40
from ADPCMi are expanded into four 16-bit uniform
PCM dual-octets on PCMo1 and PCMo2. 16-bit
uniform PCM are received and transmitted most
significant bit first starting with b15 and ending with
b0. ADPCM data are transferred most significant bit
first starting with I1 and ending with I4 for 32 kbit/s
and ending with I3 for 24 kbit/s operation (i.e., I4 is
don’t care).(See Figures 5 & 8.)
16 kbit/sADPCM mode
When SEL is set to 0, the four, 2-bit ADPCM words
are transmitted/received on ADPCMo/i during the
ENB1 time-slot in SSI mode and during the B1
timeslot in ST-BUS mode. When SEL is set to 1, the
four, 2-bit ADPCM words are transmitted/received
on ADPCMo/i during the ENB2 timeslot in SSI mode
and during the B2 timeslot in ST-BUS mode. (See
Figures 5 & 8.)
PCM Law Control (A/μ, FORMAT)
The PCM companding/coding law invoked by the
transcoder is controlled via the A/μ and FORMAT
pins. ITU-T G.711 companding curves, μ-Law and
A-Law, are selected by the A/μ pin (0=μ-Law;
1=A-Law). Per sample, digital code assignment can
conform to ITU-T G.711 (when FORMAT=1) or to
Sign-Magnitude coding (when FORMAT=0). Table 1
illustrates these choices.
Table 1 - Companded PCM
Power Down
Setting the PWRDN pin low will asynchronously
cause all internal operation to halt and the device to
go to a power down condition where no internal
clocks are running. Output pins C2o, EN1, EN2,
PCMo1, PCMo2 and ADPCMo and I/O pin F0od/
ENB2 are forced to a high-impedance state.
Following the reset (i.e., PWRDN pin brought high)
FORMAT
0
1
PCM Code
Sign-
Magnitude
A/μ = 0 or 1
ITU-T (G.711)
(A/μ = 0)
(A/μ = 1)
+ Full Scale
1111 1111
1000 0000 1010 1010
+ Zero
1000 0000
1111 1111 1101 0101
- Zero
0000 0000
0111 1111 0101 0101
- Full Scale
0111 1111
0000 0000 0010 1010
and assuming that clocks are applied to the MCLK
and BCLK pins, the internal clocks will still not begin
to operate until the first frame alignment is detected
on the ENB1 pin for SSI mode or on the F0i pin for
ST-BUS mode. The C2o clock and EN1, EN2 pins
will not start operation until a valid frame pulse is
applied to the F0i pin. If the F0i pin remains low for
longer than 2 cycles of MCLK then the C2o pin will
top toggling and will stay low. If the F0i pin is held
high then the C2o pin will continue to operate. In ST-
BUS mode the EN1 and EN2 pins will stop toggling if
the frame pulse (F0i) is not applied every frame.
Master Clock (MCLK)
A minimum 4096 kHz master clock is required for
execution of the transcoding algorithm. The
algorithm requires 512 cycles of MCLK during one
frame for proper operation. For SSI operation this
input, at the MCLK pin, may be asynchronous with
the 8 kHz frame provided that the lowest frequency
and deviation due to clock jitter still meets the strobe
period requirement of a minimum of 512 t
C4P
-
25%t
C4P
(see Figure 3). For example, a system
producing large jitter values can be accommodated
by running an over-speed MCLK that will ensure a
minimum 512 MCLK cycles per frame is obtained.
The minimum MCLK period is 61 nSec, which
translates to a maximum frequency of 16.384 MHz.
Extra MCLK cycles (>512/frame) are acceptable
since the transcoder is aligned by the appropriate
strobe signals each frame.
Figure 3 - MCLK Minimum Requirement
Bit Clock (BCLK)
For SSI operation the bit rate, for both ADPCM and
PCM ports, is determined by the clock input at BCLK.
BCLK must be eight periods in duration and
synchronous with the 8 kHz frame inputs at ENB1
and ENB2. Data is sampled at PCMi1/2 and at
ADPCMi concurrent with the falling edge of BCLK.
Data is available at PCMo1/2 and ADPCMo
concurrent with the rising edge of BCLK. BCLK may
be any rate between 128 kHz and 4096 kHz. For ST-
BUS operation BCLK is ignored (tie to V
SS
) and the
bit rate is internally set to 2048 kbit/s.
ENB1
MCLK
512 t
C4P
- 25%t
C4P
Minimum
相關PDF資料
PDF描述
MT9126AS CMOS Quad ADPCM Transcoder
MT9126 Quad ADPCM Transcoder(四ADPCM編解碼器)
MT9160B ISO2-CMOS 5 Volt Multi-Featured Codec (MFC)
MT9160BE ISO2-CMOS 5 Volt Multi-Featured Codec (MFC)
MT9160BS ISO2-CMOS 5 Volt Multi-Featured Codec (MFC)
相關代理商/技術參數
參數描述
MT9126AE1 制造商:Microsemi Corporation 功能描述:ADPCM VOICE COMPRESSION G.726 16KBPS/24KBPS/32KBPS 5V 28PDIP - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TRANSCODER QUAD ADPCM 28PDIP 制造商:Microsemi Corporation 功能描述:IC TRANSCODER QUAD ADPCM 28PDIP
MT9126AS 制造商:Microsemi Corporation 功能描述:
MT9126AS1 制造商:Microsemi Corporation 功能描述:ADPCM VOICE COMPRESSION G.726 16KBPS/24KBPS/32KBPS 5V 28SOIC - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TRANSCODER QUAD ADPCM 28SOIC 制造商:Microsemi Corporation 功能描述:IC TRANSCODER QUAD ADPCM 28SOIC
MT9126ASR 制造商:Microsemi Corporation 功能描述:
MT9126ASR1 制造商:Microsemi Corporation 功能描述:ADPCM VOICE COMPRESSION G.726 16KBPS/24KBPS/32KBPS 5V 28SOIC - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TRANSCODER QUAD ADPCM 28SOIC 制造商:Microsemi Corporation 功能描述:IC TRANSCODER QUAD ADPCM 28SOIC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*