- 您現在的位置：買賣IC網 > PDF目錄383644 > MT9042C (Mitel Networks Corporation) Multitrunk System Synchronizer(多中繼系統同步裝置) PDF資料下載
參數資料
| 型號： | MT9042C |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Multitrunk System Synchronizer(多中繼系統同步裝置) |
| 中文描述： | Multitrunk系統同步器（多中繼系統同步裝置） |
| 文件頁數： | 3/28頁 |
| 文件大小： | 126K |
| 代理商： | MT9042C |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
MT9042C
3
Notes:
1. All inputs are CMOS with either TTL compatible logic levels, CMOS compatible logic levels or Schmitt trigger compatible logic levels
as indicated in the Pin Description.
2. All outputs are CMOS with CMOS compatible logic levels.
3. See DC Electrical Characteristics for static logic threshold values.
4. See AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels for dynamic logic threshold values.
5. Unless otherwise stated, all unused inputs should be connected to logic high or logic low and all unused outputs should be left open
circuit.
16
C8o
Clock 8.192MHz (CMOS Output).
This output is used for ST-BUS operation at 8.192Mb/s.
17
C16o
Clock 16.384MHz (CMOS Output).
This output is used for ST-BUS operation at 16.384Mb/s.
19
GTi
Guard Time (Schmitt Input).
This input is used by the MT9042B state machine in both
Manual and Automatic modes. The signal at this pin affects the state changes between
Primary Holdover Mode and Primary Normal Mode, and Primary Holdover Mode and
Secondary Normal Mode. The logic level at this input is gated in by the rising edge of F8o.
See Tables 4 and 5.
20
GTo
Guard Time (CMOS Output).
The LOS1 input is gated by the rising edge of F8o, buffered
and output on GTo. This pin is typically used to drive the GTi input through an RC circuit.
21
LOS2
Secondary Reference Loss (TTL Input).
This input is normally connected to the loss of
signal (LOS) output signal of a Line Interface Unit (LIU). When high, the SEC reference signal
is lost or invalid. LOS2, along with the LOS1 and GTi inputs control the MT9042B state
machine when operating in Automatic Control. The logic level at this input is gated in by the
rising edge of F8o.
22
LOS1
Primary Reference Loss (TTL Input).
Typically, external equipment applies a logic high to
this input when the PRI reference signal is lost or invalid. The logic level at this input is gated
in by the rising edge of F8o. See LOS2 description.
23
MS2
Mode/Control Select 2 (TTL Input).
This input, in conjunction with MS1, determines the
device’s mode (Automatic or Manual) and state (Normal, Holdover or Freerun) of operation.
The logic level at this input is gated in by the rising edge of F8o. See Table 3.
24
MS1
Mode/Control Select 1 (TTL Input).
The logic level at this input is gated in by the rising
edge of F8o. See pin description for MS1.
25
RSEL
Reference Source Select (TTL Input).
In Manual Control, a logic low selects the PRI
(primary) reference source as the input reference signal and a logic high selects the SEC
(secondary) input. In Automatic Control, this pin must be at logic low. The logic level at this
input is gated in by the rising edge of F8o. See Table 2.
26
FS2
Frequency Select 2 (TTL Input).
This input, in conjunction with FS1, selects which of three
possible frequencies (8kHz, 1.544MHz, or 2.048MHz) may be input to the PRI and SEC
inputs. See Table 1.
27
FS1
Frequency Select 1 (TTL Input).
See pin description for FS2.
28
RST
Reset (Schmitt Input).
A logic low at this input resets the MT9042C. To ensure proper
operation, the device must be reset after changes to the method of control, reference signal
frequency changes and power-up. The RST pin should be held low for a minimum of 300ns.
While the RST pin is low, all frame and clock outputs are at logic high. Following a reset, the
input reference source and output clocks and frame pulses are phase aligned as shown in
Figure 19.
Pin Description
Pin #
Name
Description (see notes 1 to 5)
相關PDF資料 |
PDF描述 |
|---|---|
| MT9043 | T1/E1 System Synchronizer(T1/E1 系統同步裝置（由一個數字鎖相環組成）) |
| MT9044 | T1/E1/OC3 System Synchronizer(T1/E1/OC3 系統同步裝置（由一個數字鎖相環組成）) |
| MT90500 | Multi-Channel ATM AAL1 SAR(多通道 ATM AAL1分段及重組設備（基于通訊總線的系統與ATM網絡的接口）) |
| MT90500 | Multi-Channel ATM AAL1 SAR |
| MT90500AL | Multi-Channel ATM AAL1 SAR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9042CP | 制造商:Microsemi Corporation 功能描述: 制造商:Mitel Networks Corporation 功能描述: |
| MT9042CP1 | 制造商:Microsemi Corporation 功能描述:SYNCHRONIZER 28PLCC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE MULTITRUNK SYSTEM SYNCHRONIZER 制造商:Zarlink Semiconductor Inc 功能描述:SYNCHRONIZER 28PLCC - Rail/Tube 制造商:Zarlink Semiconductor Inc 功能描述:PB FREE MULTITRUNK SYSTEM SYNCHRONIZER |
| MT9042CPR1 | 制造商:Microsemi Corporation 功能描述:SYNCHRONIZER 28PLCC - Tape and Reel 制造商:Zarlink Semiconductor Inc 功能描述:SYNCHRONIZER 28PLCC - Tape and Reel |
| MT9043 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 System Synchronizer |
| MT9043AN | 制造商:Microsemi Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。