- 您現在的位置：買賣IC網 > PDF目錄383643 > MT8977 (Mitel Networks Corporation) Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 PDF資料下載
參數資料
| 型號： | MT8977 |
| 廠商： | Mitel Networks Corporation |
| 元件分類： | 通信及網絡 |
| 英文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 中文描述： | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| 文件頁數： | 8/30頁 |
| 文件大?。?/td> | 200K |
| 代理商： | MT8977 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
MT8977
ISO-CMOS
Preliminary Information
4-66
.
Table 2. Master Control Word 2 (Channel 31, CSTi0)
Bit
Name
Description
7
RMLOOP
Remote Loopback.
When set, the data received at RxA and RxB is looped back to TxB and TxA
respectively. The data is clocked into the device with E1.5i. The device still monitors the received
data and outputs it at DSTo. The device operates normally when the bit is clear.
Digital Loopback.
When set, the data input on DSTi is looped around to DSTo. The normal received
data on RxA, RxB and RxD is ignored. However, the data input at DSTi is still transmitted on TxA
and TxB. The device frames up on the looped data using the C1.5i clock.
All One’s Alarm.
When set, the chip transmits an unframed all 1's signal on TxA and TxB.
ESF/D4 Select.
When set, the device is in ESF mode. When clear, the device is in D3/D4 mode.
Reframe.
If set for at least one frame and then cleared, the chip will begin to search for a new frame
position. Only the change from high to low will cause a reframe, not a continuous low level.
SLC-96 Mode Select.
The chip is in SLC-96 mode when this bit is set. This enables input and
output of the F
S
bit pattern using the same pins as the facility data link in ESF mode. The chip will
use the same framing algorithm as D3/D4 mode. The user must insert the valid F
S
bits in 2 out of 6
superframes to allow the receiver to find superframe sync, and the transmitter to insert A and B bits
in every 6
th
frame. The SLC-96 FDL completely replaces the F
S
pattern in the outgoing S bit position.
Inactive in ESF mode.
In ESF mode, when set, the chip disregards the CRC calculation during synchronization. When
clear, the device will check for a correct CRC before going into synchronization. In D3/D4 mode,
when set, the device will synchronize on the first correct S-bit pattern detected. When this bit is
clear, the device will not synchronize if it has detected more than one candidate for the frame
alignment pattern (i.e., a mimic).
Maintenance Mode.
When set, the device will declare itself out-of-sync if 4 out of 12 consecutive F
T
bits are in error. When clear, the out-of-sync threshold is 2 errors in 4 F
T
bits. In this mode, four
consecutive bits following an errored F
T
bit are examined.
6
DGLOOP
5
4
3
ALL1'S
ESF/D4
ReFR
2
SLC-96
1
CRC/MIMIC
0
Maint.
allows the device to interface with systems that have
already applied some form of zero code suppression
to the data input on DSTi. B8ZS zero code
suppression replaces all strings of 8 zeros with a
known bit pattern and a specific pattern of bipolar
violations. This bit pattern and violation pattern is
shown in Figure 7. The receiver monitors the
received bit pattern and the bipolar violation pattern
and replaces all matching strings with 8 zeros.
Loopback Modes
Remote and digital loopback modes are enabled by
bits 6 and 7 in Master Control Word 2. These modes
can be used for diagnostics in locating the source of a
fault condition. Remote loop around loops back data
received at RxA and RxB back out on TxA and TxB,
thus effectively sending the received DS1 data back
to the far end unaltered so that the transmission line
can be tested. The received signal is still monitored
with the appropriate received channels on the DS1
side made available in the proper format at DSTo.
The digital loop around mode diverts the data
received at DSTi back out the DSTo pin. Data
received on DSTi is, however, still transmitted out via
TxA and TxB. This loop back mode can be used to
test the near end interface equipment when there is
no transmission line or when there is a suspected
failure of the line.
The all one’s transmit alarm (also known as the blue
alarm or the keep alive signal) can be activated in
conjunction with the digital loop around so that the
transmission line sends an all 1's signal while the
normal data is looped back locally.
The MT8977 also has a per channel loopback mode.
See Table 6 and the following section for more
information.
Per Channel Control Features
In addition to the two master control words in CSTi0
there are also 24 Per Channel Control Words. These
control words only affect individual DS0 channels.
The correspondence between the channels on CSTi0
and the affected DS0 channel is shown in Fig. 6.
相關PDF資料 |
PDF描述 |
|---|---|
| MT8977 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT8977AC | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT8977AE | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT8977AP | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
| MT8979 | Ultraframer DS3/E3/DS2/E2/DS1/E1/DS0 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8977AC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY T1/ESF Framer Circuit |
| MT8977AE | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY T1/ESF Framer Circuit |
| MT8977AP | 制造商:Rochester Electronics LLC 功能描述: 制造商:Mitel Networks Corporation 功能描述: 制造商:Zarlink Semiconductor Inc 功能描述: 制造商:ZARLINK 功能描述: |
| MT8977APR | 制造商:Rochester Electronics LLC 功能描述: 制造商:Zarlink Semiconductor Inc 功能描述: 制造商:ZARLINK 功能描述: |
| MT8979 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:ISO-CMOS ST-BUS⑩ FAMILY CEPT PCM 30/CRC-4 Framer & Interface |
發布緊急采購，3分鐘左右您將得到回復。