- 您現在的位置：買賣IC網 > PDF目錄383642 > MT88E39AS (Mitel Networks Corporation) XLR Style Audio Connector PDF資料下載
參數資料
| 型號： | MT88E39AS |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | XLR Style Audio Connector |
| 中文描述： | 主叫號碼識別的CMOS電路（CNIC1.1） |
| 文件頁數： | 3/14頁 |
| 文件大?。?/td> | 98K |
| 代理商： | MT88E39AS |
Advance Information
MT88E39
5-3
Functional Description
The MT88E39 is a FSK demodulator compatible with
FSK based Caller ID services around the world, such
as in North America, France, Germany, and Japan.
Caller ID is the generic term for a group of services
offered by telephone operating companies whereby
information about the calling party is delivered to the
subscriber. In the FSK based methods, the
information is modulated in either Bell 202 (in North
America) or CCITT V.23 (in Europe) FSK format and
transmitted at 1200 baud from the serving end office
to the subscriber’s terminal.
In North America, Caller ID uses the voiceband data
transmission interface defined in the Bellcore
document GR-30-CORE. The terminal or CPE
(Customer Premises Equipment) requirements are
defined in Bellcore document SR-TSV-002476.
Typical services are CND (Calling Number Delivery),
CNAM (Calling Name Delivery), VMWI (Visual
Message Waiting Indicator) and CIDCW (Calling
Identity Delivery on Call Waiting).
In on-hook Caller ID, such as CND and CNAM, the
information is typically transmitted from the end
office before the subscriber picks up the phone.
There are various methods such as between the first
and second rings (North America), between an
abbreviated ring and the first true ring (Japan,
France and Germany). On-hook Caller ID can also
occur without ringing for services such as VMWI.
The MT88E39 is suitable for these forms of alerting.
In off-hook Caller ID, such as CIDCW, information
about a new calling party is sent to the subscriber
who is already engaged in a call. Bellcore’s method
uses a special dual tone known as CAS (CPE
Alerting Signal) which should be detected by the
CPE. After the CPE has acknowledged with a DTMF
digit, the end office will send the FSK data. The
MT88E39 is suitable for receiving the FSK data but a
separate CAS detector is required.
The MT88E39 provides an interface to the Caller ID
physical layer. It bandpass filters and demodulates
the 1200 baud FSK signal. It also provides a
convenient interface to extract the demodulated FSK
data. Although the main application of the MT88E39
is Caller ID, it can also be used wherever 1200 baud
Bell 202 and/or CCITT V.23 FSK reception is
required.
3 to 5V operation
The MT88E39 can operate from 5.5V down to 2.7V,
but the FSK reject level will change with Vdd. In a
battery powered CPE, the FSK accept level will
become lower as the batteries are run down. If the
CPE is designed for 4.5V, the accept level will be
lowered when the batteries drain to 3V. In North
America there is a requirement for rejecting FSK
signals which are below 3 mVrms when data is not
preceded by ringing, such as VMWI (Visual Message
Waiting Indicator) applications. When the batteries
are drained, the CPE will not meet the reject level.
For on-hook Caller ID, there is no reject level and the
CPE will meet all requirements.
Input Configuration
The input arrangement of the MT88E39 provides an
operational amplifier, as well as a bias source (V
Ref
)
which is used to bias the inputs at V
DD
/2
. Provision is
made for connection of a feedback resistor to the
op-amp output (GS) for adjustment of gain.
Figure 3 shows the necessary connections for a
differential input configuration. In a single-ended
configuration, the input pins are connected as shown
in Figure 4.
14
MODE
Mode select (Input).
This pin selects the 3-wire FSK interface mode. To select mode 0
(MT88E41 compatible mode) this pin should be logic low. To select mode 1 this pin should be
logic high.
Because this pin is already connected to Vss in ’E41 applications, the MT88E39 can replace
the ’E41 without any circuit or software change.
15
IC
Internal Connection.
Internal connection. Leave open circuit. In MT88E41, this was IC2
which was also left open in the application circuit.
16
V
DD
Positive power supply voltage.
Pin Description
Pin #
Name
Description
相關PDF資料 |
PDF描述 |
|---|---|
| MT88E43B | Extended Voltage Calling Number Identification Circuit (ECNIC)(擴展電壓主叫識別電路（接收傳送的物理層信號）) |
| MT88L85 | 3V Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT88L85AE | 3V Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT88L85AN | 3V Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
| MT88L85AP | 3V Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT88E39AS1 | 制造商:Microsemi Corporation 功能描述:CALLER ID CMOS 3.58MHZ 3.3V/5V 16SOIC - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CNIC1.1 CLIP CID TYPE1 16SOIC 制造商:Microsemi Corporation 功能描述:IC CNIC1.1 CLIP CID TYPE1 16SOIC |
| MT88E39ASR | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Calling Number Identification Circuit |
| MT88E39ASR1 | 制造商:Microsemi Corporation 功能描述:Pb Free CNIC 1.1 制造商:Microsemi Corporation 功能描述:CALLER ID CMOS 3.58MHZ 3.3V/5V 16SOIC - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC CNIC1.1 CLIP CID TYPE1 16SOIC 制造商:Microsemi Corporation 功能描述:IC CNIC1.1 CLIP CID TYPE1 16SOIC |
| MT88E41 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:CMOS Extended Voltage Calling Number Identification Circuit (ECNIC) |
| MT88E41AE | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:CMOS Extended Voltage Calling Number Identification Circuit (ECNIC) |
發布緊急采購，3分鐘左右您將得到回復。