- 您現在的位置：買賣IC網 > PDF目錄374523 > MSK5211 (MS KENNEDY CORP) DUAL +/- VOLTAGE REGULATOR PDF資料下載
參數資料
| 型號： | MSK5211 |
| 廠商： | MS KENNEDY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | DUAL +/- VOLTAGE REGULATOR |
| 中文描述： | DUAL OUTPUT, FIXED MIXED REGULATOR, PDFP20 |
| 封裝： | DFP-20 |
| 文件頁數： | 3/6頁 |
| 文件大小： | 452K |
| 代理商： | MSK5211 |
APPLICATION NOTES
HEAT SINKING
To determine if a heat sink is required for your application
and if so, what type, refer to the thermal model and govern-
ing equation below.
Governing Equation: Tj = Pd x (R
θ
jc + R
θ
cs + R
θ
sa) + Ta
WHERE
Tj = Junction Temperature
Pd = Total Power Dissipation
R
θ
jc = Junction to Case Thermal Resistance
R
θ
cs = Case to Heat Sink Thermal Resistance
R
θ
sa = Heat Sink to Ambient Thermal Resistance
Tc = Case Temperature
Ta = Ambient Temperature
Ts = Heat Sink Temperature
EXAMPLE:
This example demonstrates an analysis where the output cur-
rents are at 0.5 amp each and both inputs are 8V.
Conditions for MSK 5211:
+Vin = +8.0V; Iout = 0.5A Positive Regulator
1.) Assume 45° heat spreading model.
2.) Find positive regulator power dissipation:
Pd = (Vin - Vout)(Iout)
Pd = (+8V-5V)(0.5A)
Pd = 1.5W
3.) For conservative design, set Tj = +125°C Max.
4.) For this example, worst case Ta = +85°C.
5.) R
θ
jc = 10.5°C/W from the Electrical Specification Table.
6.) R
θ
cs = 0.15°C/W for most thermal greases.
7.) Rearrange governing equation to solve for R
θ
sa:
R
θ
sa=
((Tj - Ta)/Pd) - (R
θ
jc) - (R
θ
cs)
=
(125°C-85°C)/1.5W - 13.5°C/W - 0.15°C/W
=
13.0°C/W
The same exercise must be performed for the negative regula-
tor.
PRELIMINARY Rev. - 6/06
CAPACITOR SELECTION
INPUT CAPACITOR:
An input bypass capacitor is recommenced when using the
MSK 5211 series regulators. This is especially true if the regu-
lator is located farther than 6 inches from the power supply filter
capacitors. For most applications a 1μF solid tantalum capacitor
will be suitable.
OUTPUT CAPACITOR:
A minimum of a 1μF solid tantalum capacitor should also be
used at the output to insure stability. Any increase of this out-
put capacitor larger than 10μF will only improve output imped-
ance.
+C
COMP
CAPACITOR:
For improved ripple rejection, +Ccomp can be bypassed to
ground with a 10μF tantalum capacitor. This bypass capacitor
will provide 80dB ripple rejection. Increased capacitance above
10μF does not improve the ripple rejection at frequencies above
120Hz. If the Ccomp bypass capacitor is used, it may be neces-
sary to add a protection diode to protect the regulator from ca-
pacitor discharge damage. See Typical Applications Circuit for
clarification. If the bypass capacitor is not used, it should be left
open since it is internally connected to the regulator.
3
POSITIVE REGULATOR
INPUT CAPACITOR:
Once again, if the regulator will be farther than 6 inches from
power supply filter capacitors, then an input capacitor will be
required on the negative regulator. It is recommended that a
1μF solid tantalum capacitor be used.
OUTPUT CAPACITOR:
A minimum of a 1μF solid tantalum capacitor should also be
used at the output to insure stability. Any increase of this out-
put capacitor larger than 10μF will only improve output imped-
ance.
-C
COMP
CAPACITOR:
For improved ripple rejection, -Ccomp can be bypassed to
ground with a 10μF tantalum capacitor. This bypass capacitor
will provide 66dB ripple rejection. Increased capacitance above
10μF does not improve the ripple rejection at frequencies above
120Hz. If the Ccomp bypass capacitor is used, it may be neces-
sary to add a protection diode to protect the regulator from ca-
pacitor discharge damage. See Typical Applications Circuit for
clarification. If the bypass capacitor is not used, it should be left
open since it is internally connected to the regulator.
NEGATIVE REGULATOR
It is important to keep the output connection between the regu-
lator and the load as short as possible since this directly affects
the load regulation. For example, if 20 gauge wire were used
which has a resistance of about 0.008 ohms per foot, this would
result in a drop of 8mV/ft at 1Amp of load current. It is also
important to follow the capacitor selection guidelines to achieve
best performance.
TYPICAL APPLICATION CIRCUIT
LOAD REGULATION
相關PDF資料 |
PDF描述 |
|---|---|
| MSK521XEG | DUAL +/- VOLTAGE REGULATOR |
| MSK521XG | DUAL +/- VOLTAGE REGULATOR |
| MSK521XHG | DUAL +/- VOLTAGE REGULATOR |
| MSK5215-1.5 | HIGH CURRENT, LOW DROPOUT SURFACE MOUNT VOLTAGE REGULATORS |
| MSK5215-1.5E | HIGH CURRENT, LOW DROPOUT SURFACE MOUNT VOLTAGE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSK600 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK601 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK601B | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK604 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
| MSK604B | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:NEGATIVE OUTPUT WIDE BANDWIDTH HIGH VOLTAGE AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。