參數資料
型號： MSK4322S
廠商： Electronic Theatre Controls, Inc.
英文描述： 20 AMP, 200 VOLT MOSFET SMART POWER 3-PHASE MOTOR DRIVE POWER HYBRID
中文描述： 20安培，200伏特MOSFET的智能電源3相電機驅動電源雜交
文件頁數： 4/6頁
文件大?。?/td> 324K
代理商： MSK4322S
PROTECTION
- All logic inputs use a 300nS filter. A pulse width
below this will get ignored.
-
VCC
voltage below the cutoff level of 8.65 volts
will reset all switch outputs off and ignore subse-
quent logic inputs until
VCC
is restored.
- Undervoltage lockout of the internal drivers for the
high-side switches also occurs at 8.65 volts, but will
not flag with the
FAULT
output. This may occur if
the high-side output gets switched without switch
ing the low-side. The internal boot strap power
supply for the high-side switch will sag too low for
adequate switching. The boot strap supply depends
on PWMing of the low-side switches for proper
operation.
- Switching a low-side logic input while the corre-
sponding phase high-side logic input is activated
will turn off both switches. The opposite condition
is also true. This is cross-conduction lockout and
will occur any time low and high-side inputs for a
phase are activated at the same time.
- A 2μS deadtime is automatically inserted between
high and low-side output switching to allow com-
plete turn-off of each switch so no overlap will
occur.
- An overcurrent condition detected by the
ITRIP
pin will shut down all output switches until the
overcurrent condition is removed and all three
low-side logic inputs are held high for 10μS,
then normal operation will resume.
-
ITRIP
has a 100nS leading edge blanking time
after switching to ignore any switching current
transients.
TYPICAL OPERATION
4
PRELIMINARY Rev. A 6/00
APPLICATION NOTES
MSK 4322 PIN DESCRIPTION
VCC
- Is the low voltage supply for all the internal logic
and drivers. A 0.1 μF ceramic capacitor in parallel with
a 10μF tantalum capacitor is recommended bypassing
for the VCC-VSS pins.
VSS
- Is the low voltage supply return pin and the input
logic return reference. All logic input and logic output
is referenced to this pin. This pin can vary ±5V from
the COM power return pin without affecting any of the
logic functions.
AHIN, BHIN, CHIN
- Are low active logic inputs for
signalling the corresponding phase high-side switch to
turn on. The input levels are 5V
CMOS
or
TTL
compat-
ible. Typical propagation delays are around 600nS.
ALIN, BLIN, CLIN
- Are low active inputs for sig-
nalling the corresponding phase low-side switch to turn
on. The input levels are 5V
CMOS
or
TTL
compatible.
Typical propagation delays are around 600nS.
FAULT
- Is an open drain logic output pin that gets
enabled any time the
VCC
level goes below the cutoff
point, or an overcurrent condition occurs. Bringing
VCC
back to normal levels will reset
FAULT
. Removing the
overcurrent condition and allowing the low-side logic
inputs to remain high(off) for 10μS will restore opera-
tion.
ITRIP
- Is an analog input pin for sensing current flow-
ing from the
COM
pin through a sense resistor to the
high power ground. A 0.485 volt level at this pin with
respect to
VSS
will signal an overcurrent condition,
enable the
FAULT
pin and shut down all output switch-
ing. Bringing the voltage below this point (100 mV
hysteresis) will remove the
FAULT
output and leaving
the low-side logic inputs simultaneously high (de-acti-
vated) for 10μS will restore normal operation.
V+
- Is the high voltage positive rail for the bridge.
Proper bypassing to
VSS
with sufficient capacitance to
suppress any voltage transients and to ensure remov-
ing any drooping during switching, should be done as
close to the pins on the hybrid as possible.
COM
- Is the return side of the bridge. A sense resistor
can be connected between this point and
VSS
, which
is the high voltage negative rail.
COM
can float above
and below the
VSS
pin up to 5 volts and proper opera-
tion will be maintained. Precautions should be taken
so as to not allow this voltage to get over ±5 volts
under any conditions.
A, B, C
- Are the pins connecting the 3 phase
bridge switch outputs.
相關PDF資料
PDF描述
MSK4357 28A,500V IGBT Plus Diode Smart Power 3-Phase Motor Drive Power Hybrid(28A，500V 3相位橋智能電機驅動混合電路)
MSK4361 30A,75V,3 Phase MOSFET Brushless Motor Controller(30A,75V 3相位MOSFET無電刷電機控制器)
MSK4362 30A,75V,3 Phase MOSFET Brushless Motor Controller(30A,75V 3相位MOSFET無電刷電機控制器)
MSK4362 30 AMP, 75V, 3 PHASE MOSFET BRUSHLESS MOTOR CONTROLLER
MSK4363 10A,75V,3 Phase MOSFET Brushless Motor Controller(10A,75V 3相位MOSFET無電刷電機控制器)
相關代理商/技術參數
參數描述
MSK4322U 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:20 AMP, 200 VOLT MOSFET SMART POWER 3-PHASE MOTOR DRIVE POWER HYBRID
MSK4324D 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:10 AMP, 200V, 3 PHASE MOSFET BRUSHLESS MOTOR CONTROLLER
MSK4324ED 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:10 AMP, 200V, 3 PHASE MOSFET BRUSHLESS MOTOR CONTROLLER
MSK4324ES 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:10 AMP, 200V, 3 PHASE MOSFET BRUSHLESS MOTOR CONTROLLER
MSK4324EU 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:10 AMP, 200V, 3 PHASE MOSFET BRUSHLESS MOTOR CONTROLLER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*