- 您現在的位置：買賣IC網 > PDF目錄374511 > MSK4201B (Electronic Theatre Controls, Inc.) Aluminum Electrolytic Radial Lead High Ripple, Long Life Capacitor; Capacitance: 22uF; Voltage: 350V; Case Size: 12.5x20 mm; Packaging: Bulk PDF資料下載
參數資料
| 型號： | MSK4201B |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Aluminum Electrolytic Radial Lead High Ripple, Long Life Capacitor; Capacitance: 22uF; Voltage: 350V; Case Size: 12.5x20 mm; Packaging: Bulk |
| 中文描述： | 28伏5安培MOSFET的H橋PWM電動機驅動器/放大器 |
| 文件頁數： | 4/7頁 |
| 文件大?。?/td> | 196K |
| 代理商： | MSK4201B |
This is a diagram of a typical application of the MSK 4201. The design Vcc voltage is +12 volts and should have a good low
ESR bypass capacitor such as a tantalum. The PWM and DISABLE signals are typically provided by some type of microprocessor
control. The PWM signal will be a TTL signal with a pulse frequency required by the system, and pulse duty cycles according to the
required direction/speed. A 0% duty cycle (continuous TTL low) will mean full voltage to the motor in one direction. A 100% duty
cycle (continuous TTL high) will mean full voltage to the motor in the other direction. A 50% duty cycle will hold the motor at 0
RPM.
Current sensing is done in this case by a 0.1 ohm sense resistor to sense current from either leg of the bridge. It is important
to make the high current traces as wide as possible to keep inductance down. The storage capacitor connected to the V+ and the
hybrid should be large enough to provide the high energy pulse without the voltage sagging too far. The storage capacitor should
be a low ESR ceramic capacitor or large polypropylene capacitor. Mount capacitor as close to the hybrid as possible. The
connection between GND and the V+ return should not be carrying any motor current. The sense resistor signal is common mode
filtered as necessary to feed the limiting circuitry for the microprocessor. This application will allow full four quadrant torque control
for a closed loop servo system.
A snubber network is usually required, due to the inductance in the power loop. It is important to design the snubber network
to suppress any positive spikes above 75V and negative spikes below -2V with respect to pin 5 (gnd) of the hybrid.
TYPICAL SYSTEM OPERATION
Rev. B 6/00
4
相關PDF資料 |
PDF描述 |
|---|---|
| MSK4202RH | 70V 10A Rad-Hard H-Bridge PWM Motor Driver/Amplifier(70V，10A MOSFET H橋脈寬調制電機驅動器/放大器) |
| MSK4202HRHD | 70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202HRHS | 70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202HRHU | 70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202KRHD | 70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSK4202HRHD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202HRHS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202HRHU | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202KRHD | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
| MSK4202KRHS | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:70 VOLT 10 AMP RAD-HARD H-BRIDGE PWM MOTOR DRIVER/AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。