- 您現在的位置：買賣IC網 > PDF目錄374510 > MSK153 (MS KENNEDY CORP) High Power Operational Amplifier(高電壓和磁偏轉應用的150V高工作電壓低成本運算放大器) PDF資料下載
參數資料
| 型號： | MSK153 |
| 廠商： | MS KENNEDY CORP |
| 元件分類： | 運動控制電子 |
| 英文描述： | High Power Operational Amplifier(高電壓和磁偏轉應用的150V高工作電壓低成本運算放大器) |
| 中文描述： | OP-AMP, 15000 uV OFFSET-MAX, DFM14 |
| 封裝： | POWER, HERMETIC SEALED, DIP-14 |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 352K |
| 代理商： | MSK153 |
Input protection circuitry within the MSK 153 will clip differ-
ential input voltages greater than 16 volts. The inputs are also
protected against common mode voltages up to the supply rails
as well as static discharge. There are 300 ohm current limiting
resistors in series with each input. These resistors may be-
come damaged in the event the input overload is capable of
driving currents above 1mA. If severe overload conditions are
expected, external input current limiting resistors are recom-
mended.
CURRENT LIMIT
(SEE TYPICAL CONNECTION DIAGRAM)
A value of current limit resistance can be calculated as fol-
lows:
Where:
R
CL
is the current limit resistor value
I
CL
is the current limit
0.0 *
CL
is the voltage dropped in the current limit path
across internal impedances other than the actual current
limit resistor
0.83 volts is the voltage drop that must be developed across
the current limit connections to activate the current limit
circuit
The maximum practical value of current limit resistance is 16
ohms. The current limit resistor will decrease available output
voltage swing in the following manner:
V
R
is the reduction in output voltage swing due to the current
limit resistor. It is recommended the user limit output current
to a value as close to the required output current as possible,
without clipping output voltage swing. Current limit will vary
with case temperature. Refer to the typical performance curves
to predict current limit drift. If current limit is not required
replace the resistor with a short.
SAFE OPERATING AREA (SOA)
The MOSFET output stage of this power operational ampli-
fier has two distinct limitations:
1. The current handling capability of the die metallization.
2. The junction temperature of the output MOSFET's.
NOTE: The output stage is protected against transient flyback.
However, for protection against sustained, high energy flyback,
external fast-recovery reverse biased diodes should be connected
from the output to ground.
V
R
=I
O
CL
R
R
CL
=(0.83 - (0.0 *
CL
)) / I
CL
STABILITY
The MSK 153 has sufficient phase margin when compen-
sated for unity gain to be stable with capacitive loads of at
least 10nF. However, it is recommended that the parallel sum
of the input and feedback resistor be 1000 ohms or less for
closed loop gains of ten or less to minimize phase shift caused
by the R-C network formed by the input resistor, feedback re-
sistor and input capacitance. The user can tailor the perfor-
mance of the MSK 153 to their application using the external
compensation pins. The graphs of small signal gain and phase
as well as the graphs of slew rate and power response demon-
strate the effect of various forms of compensation. The com-
pensation capacitor must be rated at 150 volts working voltage
if maximum power supply voltages are used. The compensa-
tion resistor and capacitor lead lengths must be kept as short
as possible to minimize spurious oscillations. A high quality
NPO capacitor is recommended for the compensation capaci-
tor. An effective method of checking amplifier stability is to
apply the worst case capacitive load to the output of the ampli-
fier and drive a small signal square wave across it. If overshoot
is less than 25%, the system will typically be stable.
INPUT PROTECTION
APPLICATION NOTES
TYPICAL CONNECTION DIAGRAM
CLASS "C" MODE
The user can enable class "C" mode by simply connecting
pin 8 to pin 9. This connection will disable the bias control
network in the output stage. Quiescent current will drop to 4
mA typically and a small amount of crossover distortion will
appear on the output waveform. This mode of operation is
recommended for all low frequency applications where distor-
tion is not a critical specification and quiescent power dissipa-
tion must be minimized. Disconnecting the pin 8 to pin 9 short
will enable the bias control network and the output will be bi-
ased in class AB mode again. Pin 8 should be left unconnected
when using class AB mode.(Do not ground or pull high)
Rev. A 7/00
3
相關PDF資料 |
PDF描述 |
|---|---|
| MSK154 | High Power Dual Operational Amplifier(高電壓高輸出電流的雙運算放大器) |
| MSK162 | Ultra High Voltage Operational Amplifier(350V超高電壓，60mA高輸出電流的運算放大器) |
| MSK163B | ULTRA HIGH VOLTAGE OPERATIONAL AMPLIFIER |
| MSK162 | ULTRA HIGH VOLTAGE OPERATIONAL AMPLIFIER |
| MSK162B | ULTRA HIGH VOLTAGE OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSK155 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:HIGH POWER DUAL OPERATIONAL AMPLIFIER |
| MSK155E | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:HIGH POWER DUAL OPERATIONAL AMPLIFIER |
| MSK155H | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:HIGH POWER DUAL OPERATIONAL AMPLIFIER |
| MSK161 | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:HIGH POWER CLASS C AMPLIFIER |
| MSK161B | 制造商:MSK 制造商全稱:M.S. Kennedy Corporation 功能描述:HIGH POWER CLASS C AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。