
Max.
±18
±22
±10
±250
±100
±10
-
-
-
-
-
-
-
-
-
-
V
IN
=0V
Short Pin 6 to Pin 7  V
IN
=0V
Short Pin 6 to Pin 7  V
IN
=0V
Pin 6=open  R
POT
=200
  From Pin 7 to Pin 9
V
CM
=0V
Either Input
F=DC
±10V
≤
V
S
≤
±20V
F=10Hz to 1KHz
F=1KHz
V
IN
=±14V  R
L
=1K
V
IN
=±10.5V  R
L
=100
2V step
V
IN
=1V
RMS
  R
L
=1K
V
OUT
=±10V
R
S
=100
  V
IN
=1V
RMS
  F=1KHz
1
2
3
4
5
6
7
8
9
ABSOLUTE MAXIMUM RATINGS
T
ST
T
LD
T
J
R
TH
Storage Temperature Range
Lead Temperature Range
(10 Seconds)
Junction Temperature
Thermal Resistance
Junction to Case
Output Devices Only
Supply Voltage
Output Current
Differential Input Voltage
Case Operating Temperature
(MSK 0033B)
(MSK 0033)
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
-65°C to +150°C
300°C
175°C
65°C/W
±20V
±120mA
±20V
-55°C to +125°C
-40°C to +85°C
±V
CC
I
OUT
V
IN
T
C
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
Group A
Subgroup
-
1
1
2,3
1,2,3
1
2,3
-
-
-
-
4
4
-
-
4
4
STATIC
     Supply Voltage Range
     Quiescent Current
INPUT
     Offset Voltage
     Offset Voltage Drift
     Offset Adjust
     Input Bias Current  9
     Input Impedance  3
     Power Supply Rejection Ratio  2
     Input Noise Density  3
     Input Noise Voltage  3
OUTPUT
     Output Voltage Swing
     Output Current
     Settling Time to 1%  2  3
     Bandwidth (-3dB)  3
TRANSFER CHARACTERISTICS
     Slew Rate
     Voltage Gain
Typ.
±15
±19
±2.0
±25
±50
±2
10
75
1.5
40
±12.5
±110
25
140
1500
0.99
Min.
±10
-
-
-
-
-
-
65
-
-
±12
±90
-
-
1000
0.97
Min.
±10
-
-
-
-
-
-
60
-
-
±12
±90
-
-
1000
0.95
Max.
±18
±25
±15
-
±500
-
-
-
-
-
-
-
-
-
-
-
Typ.
±15
±19
±5
-
±50
±2
10
75
1.5
40
±12.5
±110
25
140
1500
0.98
Units
V
mA
mV
μV/°C
mV
pA
nA
dB
μVRMS
nV/
√
Hz
V
mA
nS
MHz
V/μS
V/V
MSK 0033B
MSK 0033
     Parameter
Adjust to Zero
Adjust to Zero
12
12
     Test Conditions
Unless otherwise specified ±VCC = ±15 VDC.
Measured within a high speed amplifier feedback loop.
Devices shall be capable of meeting the parameter, but need not be tested.  Typical parameters are for reference only.
Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified.
Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4.
Subgroup 5 and 6 testing available upon request.
Subgroup 1,4                   T
A
=T
C
=+25°C
Subgroup 2,5                   T
A
=T
C
=+125°C
Subgroup 3,6                   T
A
=T
C
=-55°C
Electrical specifications are derated for power supply voltages other than ±15VDC.
Measurement made 0.5 seconds after application of power.  Actual DC continuous test limit is 2.5 nA at 25°C
ELECTRICAL SPECIFICATIONS
2
Rev. B  7/00
NOTES:
○
○
○
○
○
○
○
○
○
○
○
○
8
3