- 您現在的位置：買賣IC網 > PDF目錄371147 > MSB92WT1 (MOTOROLA INC) PNP GENERAL PURPOSE HIGH VOLTAGE TRANSISTORS SURFACE MOUNT PDF資料下載
參數資料
| 型號： | MSB92WT1 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 小信號晶體管 |
| 英文描述： | PNP GENERAL PURPOSE HIGH VOLTAGE TRANSISTORS SURFACE MOUNT |
| 中文描述： | 150 mA, 300 V, PNP, Si, SMALL SIGNAL TRANSISTOR |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 78K |
| 代理商： | MSB92WT1 |
3
Motorola Small–Signal Transistors, FETs and Diodes Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 1 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189
°
C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
Figure 1. Typical Solder Heating Profile
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
170
°
C
相關PDF資料 |
PDF描述 |
|---|---|
| MSC0402 | 8-bit Microcontroller with 8K EEPROM and Advanced Security Features(8位微控制器（帶8K的EEPROM和先進的安全性能）) |
| MSC0406 | 8-bit Microcontroller with 1.3K EEPROM and Advanced Security Features(8位微控制器(帶1.3K的EEPROM和先進的安全性能 ）) |
| MSC0407 | 8-bit Microcontroller with 4K EEPROM and Advanced Security Features(8位微控制器（帶4K的EEPROM和先進的安全性能 ）) |
| MSC0501 | 8-bit Microcontroller with Modular Exponentiation Unit(8位微控制器帶模塊取冪單元) |
| MSC0801 | 8-bit microcontroller for applicationsin contactless smartcards and smartcards with contacts(8位微控制器應用于無觸點的智能卡和接觸式智能卡) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSB92WT1G | 功能描述:兩極晶體管 - BJT 500mA 300V PNP RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2 |
| MSBA8100ADS | 功能描述:加速傳感器開發工具 ADS FOR MSBA8100 RoHS:否 制造商:Murata 工具用于評估:SCA3100-D04 加速:2 g 傳感軸:Triple Axis 接口類型:SPI 工作電壓:3.3 V |
| MSBG | 制造商:ADAM-TECH 制造商全稱:Adam Technologies, Inc. 功能描述:.100 MINI SHUNTS .100 [2.54] CENTERLINE |
| MSB-G | 功能描述:集管和線殼 OPEN TOP .100 GOLD PLATED RoHS:否 產品種類:1.0MM Rectangular Connectors 產品類型:Headers - Pin Strip 系列:DF50 觸點類型:Pin (Male) 節距:1 mm 位置/觸點數量:16 排數:1 安裝風格:SMD/SMT 安裝角:Right 端接類型:Solder 外殼材料:Liquid Crystal Polymer (LCP) 觸點材料:Brass 觸點電鍍:Gold 制造商:Hirose Connector |
| MSBG-02-G | 制造商:Adam Technologies Inc 功能描述:.236" OPEN TOP Green GOLD PLATED MINI SHUNT |
發布緊急采購，3分鐘左右您將得到回復。