- 您現在的位置：買賣IC網 > PDF目錄382350 > MSA1162YT1 (ON SEMICONDUCTOR) CONV DC-DC 48V IN 2.5V OUT 15W PDF資料下載
參數資料
| 型號： | MSA1162YT1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 小信號晶體管 |
| 英文描述： | CONV DC-DC 48V IN 2.5V OUT 15W |
| 中文描述： | 100 mA, 50 V, PNP, Si, SMALL SIGNAL TRANSISTOR |
| 封裝： | CASE 318D-04, SC-59, 3 PIN |
| 文件頁數： | 3/4頁 |
| 文件大?。?/td> | 44K |
| 代理商： | MSA1162YT1 |
MSA1162GT1, MSA1162YT1
http://onsemi.com
3
STEP 1
PREHEAT
ZONE 1
RAMP"
STEP 2
VENT
SOAK"
STEP 3
HEATING
ZONES 2 & 5
RAMP"
STEP 4
HEATING
ZONES 3 & 6
SOAK"
STEP 5
HEATING
ZONES 4 & 7
SPIKE"
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
T
MAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO 219
°
C
PEAK AT
SOLDER JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
Figure 1. Typical Solder Heating Profile
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
170
°
C
For any given circuit board, there will be a group of con-
trol settings that will give the desired heat pattern. The op-
erator must set temperatures for several heating zones, and
a figure for belt speed. Taken together, these control set-
tings make up a heating “profile” for that particular circuit
board. On machines controlled by a computer, the comput-
er remembers these profiles from one operating session to
the next. Figure 7 shows a typical heating profile for use
when soldering a surface mount device to a printed circuit
board. This profile will vary among soldering systems but
it is a good starting point. Factors that can affect the profile
include the type of soldering system in use, density and
types of components on the board, type of solder used, and
the type of board or substrate material being used. This pro-
file
shows
temperature
versus
time.
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches.
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
The line on the graph shows the actual temperature that
might be experienced on the surface of a test board at or
near a central solder joint. The two profiles are based on a
high density and a low density board. The Vitronics
SMD310 convection/infrared reflow soldering system was
used to generate this profile. The type of solder used was
62/36/2 Tin Lead Silver with a melting point between
177189
°
C. When this type of furnace is used for solder re-
flow work, the circuit boards and solder joints tend to heat
first. The components on the board are then heated by con-
duction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then dis-
tributes this energy to the components. Because of this ef-
fect, the main body of a component may be up to 30 degrees
cooler than the adjacent solder joints.
相關PDF資料 |
PDF描述 |
|---|---|
| MSA28 | MOLDED SSOP |
| MSC16 | MOLDED PACKAGE SSOP, EIAJ |
| MSC2295-BT1G | NPN RF Amplifier Transistors Surface Mount |
| MSC2295-CT1G | NPN RF Amplifier Transistors Surface Mount |
| MSC3930-BT1 | NPN RF Amplifier Transistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MSA1162YT1G | 功能描述:兩極晶體管 - BJT 100mA 60V PNP RoHS:否 制造商:STMicroelectronics 配置: 晶體管極性:PNP 集電極—基極電壓 VCBO: 集電極—發射極最大電壓 VCEO:- 40 V 發射極 - 基極電壓 VEBO:- 6 V 集電極—射極飽和電壓: 最大直流電集電極電流: 增益帶寬產品fT: 直流集電極/Base Gain hfe Min:100 A 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PowerFLAT 2 x 2 |
| MSA1205MD-3W | 制造商:MORNSUN 制造商全稱:MORNSUN 功能描述:DUAL/SINGLE OUTPUT DIP DC-DC CONVERTER |
| MSA1212MD-3W | 制造商:MORNSUN 制造商全稱:MORNSUN 功能描述:DUAL/SINGLE OUTPUT DIP DC-DC CONVERTER |
| MSA1215MD-3W | 制造商:MORNSUN 制造商全稱:MORNSUN 功能描述:DUAL/SINGLE OUTPUT DIP DC-DC CONVERTER |
| MSA150012A | 功能描述:線性和開關式電源 150W 12V 12.5A/15Apk RoHS:否 制造商:TDK-Lambda 產品:Switching Supplies 開放式框架/封閉式:Enclosed 輸出功率額定值:800 W 輸入電壓:85 VAC to 265 VAC 輸出端數量:1 輸出電壓（通道 1）:20 V 輸出電流（通道 1）:40 A 商用/醫用: 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:Rack 長度: 寬度: 高度: |
發布緊急采購，3分鐘左右您將得到回復。