參數資料
型號： MR83C154XXX-25P883
廠商： ATMEL CORP
元件分類： 微控制器/微處理器
英文描述： 8-BIT, MROM, 25 MHz, MICROCONTROLLER, CQCC44
封裝： LCC-44
文件頁數： 53/80頁
文件大?。?/td> 5152K
代理商： MR83C154XXX-25P883
253
XMEGA A [MANUAL]
8077I–AVR–11/2012
For reception, a fixed programmable minimum high-level pulse width for the pulse to be decoded as a logical 0 is used.
Shorter pulses will then be discarded, and the bit will be decoded to logical 1 as if no pulse was received.
The module can only be used in combination with one USART at a time. Thus, IRCOM mode must not be set for more
than one USART at a time. This must be ensured in the user software.
22.2.1 Event System Filtering
The event system can be used as the receiver input. This enables IRCOM or USART input from I/O pins or sources other
than the corresponding RX pin. If event system input is enabled, input from the USART's RX pin is automatically
disabled. The event system has a digital input filter (DIF) on the event channels that can be used for filtering. Refer to
“Event System” on page 67 for details on using the event system.
22.3
Registers Description
22.3.1 TXPLCTRL – Transmitter Pulse Length Control register
Bit 7:0 – TXPLCTRL[7:0]: Transmitter Pulse Length Control
This 8-bit value sets the pulse modulation scheme for the transmitter. Setting this register will have no effect if IRCOM
mode is not selected by a USART.
By leaving this register value to zero, 3/16 of the baud rate period pulse modulation is used.
Setting this value from 1 to 254 will give a fixed pulse length coding. The 8-bit value sets the number of system clock
periods for the pulse. The start of the pulse will be synchronized with the rising edge of the baud rate clock.
Setting the value to 255 (0xFF) will disable pulse coding, letting the RX and TX signals pass through the IRCOM module
unaltered. This enables other features through the IRCOM module, such as half-duplex USART, loop-back testing, and
USART RX input from an event channel.
TXPCTRL must be configured before the USART transmitter is enabled (TXEN).
22.3.2 RXPLCTRL – Receiver Pulse Length Control register
Bit 7:0 – RXPLCTRL[7:0]: Receiver Pulse Length Control
This 8-bit value sets the filter coefficient for the IRCOM transceiver. Setting this register will have no effect if IRCOM
mode is not selected by a USART.
By leaving this register value at zero, filtering is disabled. Setting this value between 1 and 255 will enable filtering, where
x+1 equal samples are required for the pulse to be accepted.
RXPCTRL must be configured before the USART receiver is enabled (RXEN).
Bit
76543210
+0x01
TXPLCTRL[7:0]
Read/Write
R/W
Initial Value
00000000
Bit
76543210
+0x02
RXPLCTRL[7:0]
Read/Write
R/W
Initial Value
00000000
相關PDF資料
PDF描述
MS80C51-12D 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQCC44
MT80C51T-16R 8-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP44
MD80C32E-20SC 8-BIT, 20 MHz, MICROCONTROLLER, CDIP40
MC80C52XXX-16SHXXX 8-BIT, MROM, 16 MHz, MICROCONTROLLER, CDIP40
MD80C52EXXX-20 8-BIT, MROM, 20 MHz, MICROCONTROLLER, CDIP40
相關代理商/技術參數
參數描述
MR850 功能描述:整流器 3.0 Amp 50 Volt 150ns RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel
MR850 _AY _10001 制造商:PanJit Touch Screens 功能描述:
MR850 R0 制造商:SKMI/Taiwan 功能描述:Diode Switching 50V 3A 2-Pin DO-201AD T/R
MR850_ R2 _10001 制造商:PanJit Touch Screens 功能描述:
MR850_09 制造商:PANJIT 制造商全稱:Pan Jit International Inc. 功能描述:SOFT RECOVERY, FAST SWITCHING PLASTIC RECTIFIER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*