- 您現在的位置：買賣IC網 > PDF目錄45378 > MQ80C32-12SHXXX:R (ATMEL CORP) 8-BIT, 12 MHz, MICROCONTROLLER, CQFP44 PDF資料下載
參數資料
| 型號： | MQ80C32-12SHXXX:R |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, 12 MHz, MICROCONTROLLER, CQFP44 |
| 封裝： | CERAMIC, QFP-44 |
| 文件頁數： | 160/234頁 |
| 文件大小： | 25028K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁當前第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁第195頁第196頁第197頁第198頁第199頁第200頁第201頁第202頁第203頁第204頁第205頁第206頁第207頁第208頁第209頁第210頁第211頁第212頁第213頁第214頁第215頁第216頁第217頁第218頁第219頁第220頁第221頁第222頁第223頁第224頁第225頁第226頁第227頁第228頁第229頁第230頁第231頁第232頁第233頁第234頁
31
ATtiny25/45/85 [DATASHEET]
2586Q–AVR–08/2013
6.3
System Clock Prescaler
The ATtiny25/45/85 system clock can be divided by setting the “CLKPR – Clock Prescale Register” on page 32.
This feature can be used to decrease power consumption when the requirement for processing power is low. This
can be used with all clock source options, and it will affect the clock frequency of the CPU and all synchronous
peripherals. clk
6.3.1
Switching Time
When switching between prescaler settings, the System Clock Prescaler ensures that no glitches occur in the clock
system and that no intermediate frequency is higher than neither the clock frequency corresponding to the previous
setting, nor the clock frequency corresponding to the new setting.
The ripple counter that implements the prescaler runs at the frequency of the undivided clock, which may be faster
than the CPU’s clock frequency. Hence, it is not possible to determine the state of the prescaler – even if it were
readable, and the exact time it takes to switch from one clock division to another cannot be exactly predicted.
From the time the CLKPS values are written, it takes between T1 + T2 and T1 + 2*T2 before the new clock fre-
quency is active. In this interval, 2 active clock edges are produced. Here, T1 is the previous clock period, and T2
is the period corresponding to the new prescaler setting.
6.4
Clock Output Buffer
The device can output the system clock on the CLKO pin (when not used as XTAL2 pin). To enable the output, the
CKOUT Fuse has to be programmed. This mode is suitable when the chip clock is used to drive other circuits on
the system. Note that the clock will not be output during reset and that the normal operation of the I/O pin will be
overridden when the fuse is programmed. Internal RC Oscillator, WDT Oscillator, PLL, and external clock (CLKI)
can be selected when the clock is output on CLKO. Crystal oscillators (XTAL1, XTAL2) can not be used for clock
output on CLKO. If the System Clock Prescaler is used, it is the divided system clock that is output.
6.5
Register Description
6.5.1
OSCCAL – Oscillator Calibration Register
Bits 7:0 – CAL[7:0]: Oscillator Calibration Value
The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to remove process varia-
tions from the oscillator frequency. A pre-programmed calibration value is automatically written to this register
during chip reset, giving the Factory calibrated frequency as specified in Table 21-2 on page 164. The application
software can write this register to change the oscillator frequency. The oscillator can be calibrated to frequencies
as specified in Table 21-2 on page 164. Calibration outside that range is not guaranteed.
Note that this oscillator is used to time EEPROM and Flash write accesses, and these write times will be affected
accordingly. If the EEPROM or Flash are written, do not calibrate to more than 8.8 MHz. Otherwise, the EEPROM
or Flash write may fail.
The CAL7 bit determines the range of operation for the oscillator. Setting this bit to 0 gives the lowest frequency
range, setting this bit to 1 gives the highest frequency range. The two frequency ranges are overlapping, in other
words a setting of OSCCAL = 0x7F gives a higher frequency than OSCCAL = 0x80.
The CAL[6:0] bits are used to tune the frequency within the selected range. A setting of 0x00 gives the lowest fre-
quency in that range, and a setting of 0x7F gives the highest frequency in the range.
Bit
7
654321
0
CAL7
CAL6
CAL5
CAL4
CAL3
CAL2
CAL1
CAL0
OSCCAL
Read/Write
R/W
Initial Value
Device Specific Calibration Value
相關PDF資料 |
PDF描述 |
|---|---|
| MQ80C32-20/883:R | 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44 |
| MQ80C32-20SHXXX:D | 8-BIT, 20 MHz, MICROCONTROLLER, CQFP44 |
| MQ80C32-30:RD | 8-BIT, 30 MHz, MICROCONTROLLER, CQFP44 |
| MQ80C32E-25SHXXX:D | 8-BIT, 25 MHz, MICROCONTROLLER, CQFP44 |
| MQ80C32E-36:RD | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MQ82370-20 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MQ8238020 | 制造商:Intel 功能描述:CONTROLLER: OTHER |
| MQ82380-20 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| MQ82380-20/R | 制造商:Rochester Electronics LLC 功能描述: |
| MQ82592 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。