參數資料
型號： MPR084QR2
廠商： Freescale Semiconductor
文件頁數： 15/40頁
文件大?。?/td> 0K
描述： IC CTLR TOUCH SENSOR PROX 16-QFN
標準包裝： 2,500
類型： 電容性
輸入數/鍵： 8 鍵
評估套件： 可供
數據接口： I²C，串行
電源電壓： 1.8 V ~ 3.6 V
電流 - 電源： 1.62mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 16-VQFN 裸露焊盤
供應商設備封裝： 16-QFN-EP（5x5）
包裝： 帶卷 (TR)
配用： KITMPR084EVM-ND - KIT EVAL 8-PAD TOUCH MPR084
MPR084
Sensors
22
Freescale Semiconductor
7Interrupts
7.1
Introduction
The MPR084 has one interrupt output that is configured by registers and alerts the application when a touch or fault is detected.
When running in Run2 or Stop2 mode where I2C communication is not available this feature alerts the user to sensor touches.
7.2
Condition for Interrupt
There are two cases that latch the Interrupt buffered data available or fault detected.
7.2.1
Buffered Data Available
The interrupt for Buffered Data Available will only trigger when the NDF (No Data Flag) transitions from high to low. This signifies
that there is new data available in the buffer. The interrupt is deasserted on the first read/write of the FIFO Register and cannot
be reasserted for buffered data until the FIFO is empty (either by reading all the data, or clearing the buffer).
7.2.2
Fault Detected
The interrupt for a Fault Detected condition is triggered any time the Fault condition in the Fault Register transitions from zero to
non-zero. The interrupt is deasserted when the Fault Register is cleared (by writing to the Fault Register).
7.3
Settings
Interrupts are configured through I2C using the Configuration Register (Section 4.7). Two of the settings in this register will affect
the interrupt functionality.
The Interrupt Enable (IRQEN) must be set high for the IRQ to be enabled. When low, all interrupts will be ignored, and the IRQ
pin will never latch.
The Interrupt Rate (IRQR) sets the minimum delay between sequential triggered interrupts. The minimum interrupt period can be
calculated by taking the product of the MCP (master clock period) and IRQR with a factor of 4. Thus, for the minimum setting an
interrupt would be triggered no more often than 4 times the sensor scan rate.
Equation 4
If the MPR084 is using Run2, the minimum interrupt period would be represented by the following equation.
Equation 5
7.4
IRQ Pin
The IRQ pin is an open-drain, latching interrupt output which requires an external pull-up resistor. The pin will latch down based
on the conditions in Section 6.2. The pin will reset when an I2C transmission reads/writes the appropriate register displaying
information about the source of the interrupt. Thus if the source is buffered data available then a FIFO Buffer read/write will clear
the IRQ pin. If the source is a fault detected then a write of the Fault Register will clear the pin.
MinInterruptPeriod ms
MCP
IRQR
4
=
MinInterruptPeriod ms
MTP
5
+
8
----------------------
1
+
8
I
RQR 4
=
相關PDF資料
PDF描述
MPR121QR2 IC CTLR TOUCH SENSOR 20-QFN
MX674ALCWI+T IC ADC 12BIT W/REF 28-SOIC
MX7575KN+ IC ADC 8BIT MPU COMP 18-DIP
MX7582KN+ IC ADC 12BIT 4CH 28-DIP
MX7705EWE+ IC ADC 16BIT 2CH 16-SOIC
相關代理商/技術參數
參數描述
MPR0854FPXXXZ01A 功能描述:AC/DC CONVERTER 54V 800W 制造商:ge critical power 系列:MPR，耐火 零件狀態:有效 類型:前端 輸出數:1 電壓 - 輸入:90 ~ 264 VAC 電壓 - 輸出 1:54V 電壓 - 輸出 2:- 電壓 - 輸出 3:- 電壓 - 輸出 4:- 電流 - 輸出（最大值）:14.8A 功率（W）:800W 應用:ITE（商業） 電壓 - 隔離:3kV（3000V） 效率:88% 工作溫度:-10°C ~ 70°C（有降額） 特性:熱插拔，I2C? 接口，負載均分，PFC，PMBus?，遠程開/關，遙測，待機輸出，通用輸入 安裝類型:機架安裝 大小/尺寸:8.93" 長 x 3.40" 寬 x 1.57" 高（226.8mm x 86.4mm x 39.9mm） 所需最小負載:無 認可:- 功率（W） - 最大值:800W 標準包裝:5
MPR106M2 制造商:DEARBORN ELECTRONICS INC 功能描述:CAPACITOR MILITARY FILM
MPR106M2S1 制造商:SPEC 功能描述: 制造商:Vishay Sprague 功能描述:
MPR10JB50L0 制造商:SEI Stackpole Electronics Inc 功能描述:- Bulk 制造商:SEI Stackpole Electronics Inc 功能描述:MPR10JB50L0
MPR10JB75L0 制造商:SEI Stackpole Electronics Inc 功能描述:- Bulk 制造商:SEI Stackpole Electronics Inc 功能描述:MPR10JB75L0
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*