參數資料
型號: MPR031EPR2
廠商: Freescale Semiconductor
文件頁數: 14/33頁
文件大?。?/td> 0K
描述: IC CTLR TOUCH SENSOR 8-DFN
產品培訓模塊: MPR03x - Low-Power Proximity Sensors
特色產品: MPR03x Proximity Capacitive Touch Sensor Controllers
標準包裝: 1
類型: 電容性
觸摸面板接口: 2 線
評估套件: 可供
數據接口: I²C,串行
數據速率/采樣率 (SPS,BPS): 400k
電源電壓: 1.71 V ~ 2.75 V
電流 - 電源: 43µA
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 8-UFDFN
供應商設備封裝: 8-QFN-D(2x2)
包裝: 標準包裝
產品目錄頁面: 2808 (CN2011-ZH PDF)
配用: KITMPR03XEVM-ND - KIT EVAL FOR MPR03X
DEMOMPR031-ND - BOARD DEMO FOR MPR031 CTLR
其它名稱: MPR031EPR2DKR
MPR03X
Sensors
Freescale Semiconductor
21
8.4
Third Level Filter
The Third Level Filter is designed for varying implementations. It can be used as either an additional low pass filter for the
electrode data or a baseline for touch detection. For it to function as a baseline filter, it must be used in conjunction with the touch
detection system described in the next chapter. To use the filter as an additional layer for low pass filtering, the touch detection
system must be disabled by setting all of the touch thresholds to zero (refer to Section 9.2). Although, in most cases the third
level of filter will be used as a baseline filter. The primary difference between these implementations is this: if a touch is detected
the baseline filter will hold its current value until the touch is released. The touch/release configuration will be described in
When a touch is not currently detected, the baseline filter will operate based on a few conditions. These are configured through
a set of registers including the Max Half Delta Register, the Noise Half Delta Register, and the Noise Count Limit.
8.4.1
The Max Half Delta register is used to set the Max Half Delta for the Third Level Filter. The address of the Max Half Delta Register
is 0x26.
Figure 27. Max Half Delta Register
Table 13. Filter Configuration Register Field Descriptions
Field
Description
7:5
CDT
Charge Discharge Time – The Charge Discharge Time field selects the amount
of time an electrode charges and discharges.
000 Encoding 0 – Invalid
001 Encoding 1 – Time is set to 0.5
s
010 Encoding 2 – Time is set to 1
s
~
111 Encoding 7 – Time is set to 32
s.
4:3
SFI
Second Filter Iterations – The Second Filter Iterations field selects the number of
samples taken for the second level filter.
00 Encoding 0 – Number of samples is set to 4
01 Encoding 1 – Number of samples is set to 6
10 Encoding 2 – Number of samples is set to 10
11 Encoding 3 – Number of samples is set to 18
2:0
ESI
Electrode Sample Interval – The Electrode Sample Interval field selects the
period between samples used for the second level of filtering.
000 Encoding 0 – Period set to 1 ms
001 Encoding 1 – Period set to 2 ms
~
111 Encoding 7 – Period set to 128 ms
7
6
543210
R0
0
MHD
W
Reset:
0
000000
= Unimplemented
Table 14. Max Half Delta Register Field Descriptions
Field
Description
5:0
MHD
Max Half Delta – The Max Half Delta determines the largest magnitude of
variation to pass through the third level filter.
000000 DO NOT USE THIS CODE
000001 Encoding 1 – Sets the Max Half Delta to 1
~
111111 Encoding 63 – Sets the Max Half Delta to 63
相關PDF資料
PDF描述
VE-BT0-MW-F4 CONVERTER MOD DC/DC 5V 100W
D38999/20FF28SN CONN RCPT 28POS WALL MNT W/SCKT
VE-BT0-MW-F2 CONVERTER MOD DC/DC 5V 100W
MS3106A36-1S CONN PLUG 22POS STRAIGHT W/SCKT
MS27473E14B37P CONN PLUG 37POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
MPR031EPR2 制造商:Freescale Semiconductor 功能描述:IC CAPACITIVE TOUCH SENSOR FN-8
MPR031EPR2-CUT TAPE 制造商:Freescale 功能描述:MPR031 Series 2.75 V 8 ? Proximity Capacitive Touch Sensor Controller - UDFN-8
MPR032 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Proximity Capacitive Touch Sensor Controller
MPR032EP 制造商:Freescale Semiconductor 功能描述:CAPACITIVE TOUCH SENSOR 8-PIN UDFN BULK - Bulk
MPR032EPR2 功能描述:電容觸摸傳感器 DFN TOUCH PAD RoHS:否 制造商:Microchip Technology 電源電壓: 通道數量: 封裝 / 箱體: 尺寸: 溫度范圍: