- 您現在的位置：買賣IC網 > PDF目錄9028 > MPC9653AACR2 (IDT, Integrated Device Technology Inc)IC PLL CLK GEN 1:8 3.3V 32-LQFP PDF資料下載
參數資料
| 型號： | MPC9653AACR2 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PLL CLK GEN 1:8 3.3V 32-LQFP |
| 標準包裝： | 2,000 |
| 類型： | PLL 時鐘發生器 |
| PLL： | 帶旁路 |
| 輸入： | LVCMOS，LVPECL |
| 輸出： | LVCMOS |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:8 |
| 差分 - 輸入:輸出： | 是/無 |
| 頻率 - 最大： | 125MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-LQFP |
| 供應商設備封裝： | 32-TQFP（7x7） |
| 包裝： | 帶卷 (TR) |
MPC9653A REVISION 4 JANUARY 8, 2013
7
2013 Integrated Device Technology, Inc.
MPC9653A Data Sheet
3.3 V 1:8 LVCMOS PLL CLOCK GENERATOR
Calculation of Part-to-Part Skew
The MPC9653A zero delay buffer supports applications
where critical clock signal timing can be maintained across
several devices. If the reference clock inputs of two or more
MPC9653As are connected together, the maximum overall
timing uncertainty from the common PCLK input to any output
is:
tSK(PP) = t() + tSK(O) + tPD, LINE(FB) + tJIT() CF
This maximum timing uncertainty consist of 4 components:
static phase offset, output skew, feedback board trace delay
and I/O (phase) jitter:
Figure 4. MPC9653A Maximum Device-to-Device Skew
Due to the statistical nature of I/O jitter a RMS value (1
)
is specified. I/O jitter numbers for other confidence factors
(CF) can be derived from Table 8.
The feedback trace delay is determined by the board
layout and can be used to fine-tune the effective delay
through each device. In the following example calculation a
I/O jitter confidence factor of 99.7% (
3) is assumed,
resulting in a worst case timing uncertainty from input to any
output of –197 ps to 297 ps (at 125 MHz reference frequency)
relative to PCLK:
tSK(PP) = [-17ps...117ps] + [-150ps...150ps] +
[(10ps @ -3)...(10ps @ 3)] + tPD, LINE(FB)
tSK(PP) = [-197ps...297ps] + tPD, LINE(FB)
Due to the frequency dependence of the I/O jitter,
Figure 5, can be used for a more precise timing performance
analysis.
Figure 5. Maximum I/O Jitter versus Frequency
Driving Transmission Lines
The MPC9653A clock driver was designed to drive high
speed signals in a terminated transmission line environment.
To provide the optimum flexibility to the user the output
drivers were designed to exhibit the lowest impedance
possible. With an output impedance of less than 20
the
drivers can drive either parallel or series terminated
transmission lines. For more information on transmission
lines the reader is referred to Freescale Semiconductor
application note AN1091. In most high performance clock
networks point-to-point distribution of signals is the method of
choice. In a point-to-point scheme either series terminated or
parallel terminated transmission lines can be used. The
parallel technique terminates the signal at the end of the line
with a 50
resistance to VCC 2.
This technique draws a fairly high level of DC current and
thus only a single terminated line can be driven by each
output of the MPC9653A clock driver. For the series
terminated case however there is no DC current draw, thus
the outputs can drive multiple series terminated lines.
Figure 5, illustrates an output driving a single series
terminated line versus two series terminated lines in parallel.
When taken to its extreme the fanout of the MPC9653A clock
driver is effectively doubled due to its capability to drive
multiple lines.
Table 8. Confidence Factor CF
CF
Probability of clock edge within the distribution
1
0.68268948
2
0.95449988
3
0.99730007
4
0.99993663
5
0.99999943
6
0.99999999
tPD,LINE(FB)
tJIT()
+tSK(O)
—t()
+t()
tJIT()
+tSK(O)
tSK(PP)
Max. skew
PCLKCommon
QFBDevice 1
Any QDevice 1
QFBDevice2
Any QDevice 2
30
20
10
0
25 35
45
55
65
75
85
95
105 115
125
FB =
8FB = 4
3I
/O
J
itt
er
[p
s]
RMS
Reference Frequency [MHz]
相關PDF資料 |
PDF描述 |
|---|---|
| VE-J72-MZ-F3 | CONVERTER MOD DC/DC 15V 25W |
| MPC9653AAC/W | IC PLL CLK GEN 1:8 3.3V 32-LQFP |
| VE-23F-MW-F4 | CONVERTER MOD DC/DC 72V 100W |
| VE-23F-MW-F3 | CONVERTER MOD DC/DC 72V 100W |
| VI-24T-MY-F2 | CONVERTER MOD DC/DC 6.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC9653AACR2/W | 功能描述:IC PLL CLK GEN 1:8 3.3V 32-LQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| MPC9653AC | 功能描述:時鐘發生器及支持產品 3.3V 125MHz Clock Generator RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MPC9653AFA | 功能描述:時鐘發生器及支持產品 3.3V 125MHz Clock Generator RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MPC9653AFAR2 | 功能描述:IC PLL CLK GENERATOR 1:8 32-LQFP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MPC9653FA | 功能描述:時鐘發生器及支持產品 3.3V 125MHz Clock Generator RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
發布緊急采購，3分鐘左右您將得到回復。