- 您現在的位置：買賣IC網 > PDF目錄98027 > MPC9230AC (INTEGRATED DEVICE TECHNOLOGY INC) 750 MHz, OTHER CLOCK GENERATOR, PQFP32 PDF資料下載
參數資料
| 型號： | MPC9230AC |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 750 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, LEAD FREE, O.80 MM PITCH, MS-026BBA, LQFP-32 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 795K |
| 代理商： | MPC9230AC |
MPC9230 REVISION 8 MARCH 29, 2010
10
2010 Integrated Device Technology, Inc.
MPC9230 Data Sheet
800MHZ LOW VOLTAGE PECL CLOCK SYNTHESIZER
Figure 4. Serial Interface Timing Diagram
Power Supply Filtering
The MPC9230 is a mixed analog/digital product. Its analog
circuitry is naturally susceptible to random noise, especially if this
noise is seen on the power supply pins. Random noise on the
VCC_PLL pin impacts the device characteristics. The MPC9230
provides separate power supplies for the digital circuitry (VCC) and
the internal PLL (VCC_PLL) of the device. The purpose of this design
technique is to try and isolate the high switching noise digital outputs
from the relatively sensitive internal analog phase-locked loop. In a
controlled environment such as an evaluation board, this level of
isolation is sufficient; however, in a digital system environment
where it is more difficult to minimize noise on the power supplies, a
second level of isolation may be required. The simplest form of
isolation is a power supply filter on the VCC_PLL pin for the
MPC9230. Figure 5 illustrates a typical power supply filter scheme.
The MPC9230 is most susceptible to noise with spectral content in
the 1 kHz to 1 MHz range. Therefore, the filter should be designed
to target this range. The key parameter that needs to be met in the
final filter design is the DC voltage drop that will be seen between
the VCC supply and the MPC9230 pin of the MPC9230. From the
data sheet, the VCC_PLL current (the current sourced through the
VCC_PLL pin) is maximum 20 mA, assuming that a minimum of
2.835 V must be maintained on the VCC_PLL pin. The resistor shown
in Figure 5 must have a resistance of 10–15
to meet the voltage
drop criteria. The RC filter pictured will provide a broadband filter
with approximately 100:1 attenuation for noise whose spectral
content is above 20 kHz. As the noise frequency crosses the series
resonant point of an individual capacitor, its overall impedance
begins to look inductive and thus increases with increasing
frequency. The parallel capacitor combination shown ensures that a
low impedance path to ground exists for frequencies well above the
bandwidth of the PLL. Generally, the resistor/capacitor filter will be
cheaper, easier to implement and provide an adequate level of
supply filtering. A higher level of attenuation can be achieved by
replacing the resistor with an appropriate valued inductor. A
1000
H choke will show a significant impedance at 10 kHz
frequencies and above. Because of the current draw and the voltage
that must be maintained on the VCC_PLL pin, a low DC resistance
inductor is required (less than 15
).
Figure 5. VCC_PLL Power Supply Filter
Layout Recommendations
The MPC9230 provides sub-nanosecond output edge rates and
thus a good power supply bypassing scheme is a must. Figure 6
shows a representative board layout for the MPC9230. There exists
many different potential board layouts, and the one pictured is but
one. The important aspect of the layout in Figure 6 is the low
impedance connections between VCC and GND for the bypass
capacitors. Combining good quality general purpose chip capacitors
with good PCB layout techniques will produce effective capacitor
resonances at frequencies adequate to supply the instantaneous
switching current for the MPC9230 outputs. It is imperative that low
inductance chip capacitors are used; it is equally important that the
board layout does not reintroduce all of the inductance saved by
using the leadless capacitors. Thin interconnect traces between the
capacitor and the power plane should be avoided, and multiple large
vias should be used to tie the capacitors to the buried power planes.
Fat interconnect and large vias will help to minimize layout induced
inductance and thus maximize the series resonant point of the
bypass capacitors. Note the dotted lines circling the crystal oscillator
connection to the device. The oscillator is a series resonant circuit,
and the voltage amplitude across the crystal is relatively small. It is
imperative that no actively switching signals cross under the crystal,
as crosstalk energy coupled to these lines could significantly impact
the jitter of the device. Special attention should be paid to the layout
of the crystal to ensure a stable, jitter free interface between the
crystal and the on-board oscillator. Although the MPC9230 has
several design features to minimize the susceptibility to power
supply noise (isolated power and grounds and fully differential PLL),
there still may be applications in which overall performance is being
degraded due to system power supply noise. The power supply filter
S_CLOCK
S_DATA
S_LOAD
M[8:0]
N[1:0]
P_LOAD
T2 T1
T0
N1
N0
M8
M7
M6
M5
M4
M3
M2
M1
M0
M, N
First
Bit
Last
Bit
VCC_PLL
VCC
MPC9230
C1, C2 = 0.01...0.1 F
VCC
CF = 22 F
RF = 10-15
C2
C1
相關PDF資料 |
PDF描述 |
|---|---|
| MPC9230FN | 750 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| MPC9239AC | 900 MHz, OTHER CLOCK GENERATOR, PQFP32 |
| MPC92430FN | 800 MHz, OTHER CLOCK GENERATOR, PQCC28 |
| MPC92433AER2 | 1428 MHz, OTHER CLOCK GENERATOR, PQFP48 |
| MPC92433FA | 1428 MHz, OTHER CLOCK GENERATOR, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC9230ACR2 | 功能描述:時鐘合成器/抖動清除器 FSL 800MHz LVPECL Freq. Synthesizer RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC9230EI | 功能描述:時鐘合成器/抖動清除器 FSL 800MHz LVPECL Freq. Synthesizer RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC9230EIR2 | 功能描述:時鐘合成器/抖動清除器 FSL 800MHz LVPECL Freq. Synthesizer RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MPC9230FA | 功能描述:IC PECL CLOCK LV 800MHZ 32-LQFP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MPC9230FN | 功能描述:鎖相環 - PLL 3.3V 800MHz Clock Generator RoHS:否 制造商:Silicon Labs 類型:PLL Clock Multiplier 電路數量:1 最大輸入頻率:710 MHz 最小輸入頻率:0.002 MHz 輸出頻率范圍:0.002 MHz to 808 MHz 電源電壓-最大:3.63 V 電源電壓-最小:1.71 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:QFN-36 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。