參數資料
型號： MPC7410VS450NE
廠商： Freescale Semiconductor
文件頁數： 32/56頁
文件大?。?/td> 0K
描述： IC MPU 32BIT 450MHZ 360-FCCLGA
標準包裝： 44
系列： MPC74xx
處理器類型： 32-位 MPC74xx PowerPC
速度： 450MHz
電壓： 1.5V
安裝類型： 表面貼裝
封裝/外殼： 360-CLGA，F(xiàn)CCLGA
供應商設備封裝： 360-FCCLGA（25x25）
包裝： 托盤
MPC7410 RISC Microprocessor Hardware Specifications, Rev. 6.1
38
Freescale Semiconductor
System Design Information
8.4 Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal level
through a resistor. Unused active low inputs should be tied to OVDD. Unused active high inputs should be connected
to GND. All NC (no connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, OVDD, L2OVDD, and GND pins of the MPC7410.
Note that power must be supplied to L2OVDD even if the L2 interface of the MPC7410 will not be used; the
remainder of the L2 interface may be left unterminated.
8.5 Output Buffer DC Impedance
The MPC7410 60x and L2 I/O drivers are characterized over process, voltage, and temperature. To measure Z0, an
external resistor is connected from the chip pad to OVDD or GND. Then, the value of each resistor is varied until
the pad voltage is OVDD/2 (see Figure 23).
The output impedance is the average of two components, the resistances of the pull-up and pull-down devices. When
data is held low, SW2 is closed (SW1 is open), and RN is trimmed until the voltage at the pad equals (L2)OVDD/2.
RN then becomes the resistance of the pull-down devices. When data is held high, SW1 is closed (SW2 is open), and
RP is trimmed until the voltage at the pad equals (L2)OVDD/2. RP then becomes the resistance of the pull-up devices.
RP and RN are designed to be close to each other in value. Then, Z0 = (RP + RN)/2.
Figure 23 describes the driver impedance measurement circuit described above.
Figure 23. Driver Impedance Measurement Circuit
Alternately, the following is another method to determine the output impedance of the MPC7410. A voltage source,
Vforce, is connected to the output of the MPC7410, as in Figure 24. Data is held low, the voltage source is set to a
value that is equal to (L2)OVDD/2, and the current sourced by Vforce is measured. The voltage drop across the
pull-down device, which is equal to (L2)OVDD/2, is divided by the measured current to determine the output
impedance of the pull-down device, RN. Similarly, the impedance of the pull-up device is determined by dividing
the voltage drop of the pull-up, (L2)OVDD/2, by the current sank by the pull-up when the data is high and Vforce is
equal to (L2)OVDD/2. This method can be employed with either empirical data from a test setup or with data from
simulation models, such as IBIS.
OVDD
OGND
RP
RN
Pad
Data
SW1
SW2
相關PDF資料
PDF描述
IDT7007S15J IC SRAM 256KBIT 15NS 68PLCC
MPC7410VS450LE IC MPU 32BIT 450MHZ 360-FCCLGA
MPC7410VS400NE IC MPU 32BIT 400MHZ 360-FCCLGA
MC7447AVS867NB IC MPU RISC 867MHZ 360-FCCLGA
MC7447AVS600NB IC MPU RISC 600MHZ 360-FCCLGA
相關代理商/技術參數
參數描述
MPC7410VS500LE 功能描述:微處理器 - MPU NITRO R1.4 105C PB FREE RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324
MPC7441 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications
MPC7445 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications
MPC7447 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications
MPC7447A 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:RISC Microprocessor Hardware Specifications
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*