- 您現在的位置：買賣IC網 > PDF目錄359187 > MPC17531AR2 (飛思卡爾半導體(中國)有限公司) 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O PDF資料下載
參數資料
| 型號： | MPC17531AR2 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| 中文描述： | 700？毫安雙H橋電機驅動器兼容邏輯為3.0V的I / O |
| 文件頁數： | 10/19頁 |
| 文件大?。?/td> | 501K |
| 代理商： | MPC17531AR2 |
Analog Integrated Circuit Device Data
Freescale Semiconductor
10
17531A
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 17531A is a monolithic dual H-Bridge ideal for
portable electronic applications to control bipolar step motors
and brush DC motors such as those found in camera len
assemblies, camera shutters, and optical disk drives. The
device features an on-board charge pump, as well as built-in
shoot-through current protection and undervoltage
shutdown.
The 17531A has four operating modes: Forward, Reverse,
Brake, and Tri-Stated (High Impedance). The MOSFETs
comprising the output bridge have a total source + sink
R
DS(ON)
≤
1.2
.
The 17531A can simultaneously drive two brush DC
motors or one bipolar step motor. The drivers are designed to
be PWM’ed at frequencies up to 200 kHz.
FUNCTIONAL TERMINAL DESCRIPTION
LOGIC SUPPLY (VDD)
The V
DD
terminal carries the logic supply voltage and
current into the logic sections of the IC. VDD has an
undervoltage threshold. If the supply voltage drops below the
undervoltage threshold, the output power stage switches to a
tri-state condition. When the supply voltage returns to a level
that is above the threshold, the power stage automatically
resumes normal operation according to the established
condition of the input terminals.
LOGIC INPUT CONTROL (IN1A, IN1B, IN2A, AND
IN2B)
These logic input terminals control each H-Bridge output.
IN1A logic HIGH = OUT1A HIGH. However, if all inputs are
taken HIGH, the outputs bridges are both tri-stated (refer to
Table 6, Truth Table
, page
9
).
POWER SAVE (PSAVE)
The PSAVE terminal is a HIGH = TRUE power save mode
input. When PSAVE = HIGH, all H-Bridge outputs (OUT1A,
OUT1B, OUT2A, and OUT2B) are tri-stated (High-Z),
regardless of logic inputs (IN1A, IN1B, IN2A, and IN2B)
states, and the internal charge pump and low voltage
detection current are shut off to save power.
H-BRIDGE OUTPUT (OUT1A, OUT1B, OUT2A, AND
OUT2B)
These terminals provide connection to the outputs of each
of the internal H-Bridges (see
Figure 2, 17531A Simplified
Internal Block Diagram
, page
2
).
MOTOR DRIVE POWER SUPPLY (VM1 AND VM2)
The VM terminals carry the main supply voltage and
current into the power sections of the IC. This supply then
becomes controlled and/or modulated by the IC as it delivers
the power to the loads attached between the OUTput
terminals. All VM terminals must be connected together on
the printed circuit board.
CHARGE PUMP (C1L AND C1H, C2L AND C2H)
These two pairs of terminals, the C1L and C1H and the
C2L and C2H, connect to the external bucket capacitors
required by the internal charge pump. The typical value for
the bucket capacitors is 0.1
μ
F.
PREDRIVER POWER SUPPLY (CRES)
The CRES terminal is the output of the internal charge
pump. Its output voltage is approximately three times of VDD
voltage. The VCRES voltage is power supply for the internal
predriver circuit of H-Bridges.
POWER GROUND (PGND)
Power ground terminals. They must be tied together on the
PCB.
LOGIC GROUND (LGND)
Logic ground terminal.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC17531AEL | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531AEP | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531AEV | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531A | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17533EV | 0.7 A 6.8 V Dual H-Bridge Motor Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC17531ATEJ | 功能描述:IC MOTOR DRIVER PAR 20TSSOP 制造商:nxp usa inc. 系列:- 包裝:管件 零件狀態:在售 電機類型 - 步進:雙極性 電機類型 - AC，DC:有刷直流 功能:驅動器 - 全集成，控制和功率級 輸出配置:半橋（4） 接口:并聯 技術:功率 MOSFET 步進分辨率:- 應用:電池供電 電流 - 輸出:700mA 電壓 - 電源:2.7 V ~ 3.6 V 電壓 - 負載:2 V ~ 8.6 V 工作溫度:-20°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 供應商器件封裝:20-TSSOP 標準包裝:75 |
| MPC17531ATEP | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MPC17531ATEPR2 | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MPC17531ATEV | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MPC17531ATEVEL | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。