- 您現在的位置：買賣IC網 > PDF目錄359187 > MPC17529 (飛思卡爾半導體(中國)有限公司) 0.7 A Dual H-Bridge Motor Driver with 3.0V/5.0V Compatible Logic I/O(0.7 A 雙H橋電機驅動器，帶3.0V/5.0V 可兼容邏輯I/O) PDF資料下載
參數資料
| 型號： | MPC17529 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 0.7 A Dual H-Bridge Motor Driver with 3.0V/5.0V Compatible Logic I/O(0.7 A 雙H橋電機驅動器，帶3.0V/5.0V 可兼容邏輯I/O) |
| 中文描述： | 0.7甲雙H橋電動機3.0V/5.0V兼容邏輯的I / O（0.7甲雙魔橋電機驅動器，帶3.0V/5.0V可兼容程序邏輯的I / O） |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 450K |
| 代理商： | MPC17529 |
17529
8
Go to: www.freescale.com
SYSTEM/APPLICATION INFORMATION
INTRODUCTION
The 17529 is a monolithic dual H-Bridge ideal for portable
electronic applications to control bipolar step motors and brush
DC motors such as those found in camera len assemblies,
camera shutters, optical disk drives, etc. The 17529 operates
from 2.0 V to 6.8 V, providing dual H-bridge motor drivers with
parallel 3.0 V- or 5.0 V-compatible I/O. The device features an
on-board charge pump, as well as built-in shoot-through current
protection and undervoltage shutdown.
The 17529 has four operating modes: Forward, Reverse,
Brake, and Tri-Stated (High Impedance). The MOSFETs
comprising the output bridge have a total source+ sink R
DS(ON)
≤
1.2
.
The 17529 can simultaneously drive two brush DC motors
or, as shown in the simplified application diagram on page 1,
one bipolar step motor. The drivers are designed to be PWM’ed
at frequencies up to 200 kHz.
FUNCTIONAL TERMINAL DESCRIPTION
V
DD
The V
DD
terminal carries the logic supply voltage and current
into the logic sections of the IC. V
DD
has an undervoltage
threshold. If the supply voltage drops below the undervoltage
threshold, the output power stage switches to a tri-state
condition. When the supply voltage returns to a level that is
above the threshold, the power stage automatically resumes
normal operation according to the established condition of the
input terminals.
IN1A, IN1B, IN2A, and IN2B
These logic input terminals control each H-Bridge output.
IN1A logic HIGH = OUT1A HIGH. However, if all inputs are
taken HIGH, the outputs bridges are both tri-stated (refer to
Table 1, Truth Table
, page 7).
OE
The
OE
terminal is a LOW = TRUE enable input. When
OE
= HIGH, all H-Bridge outputs (OUT1A, OUT1B, OUT2A,
and OUT2B) are tri-stated (high-impedance), regardless of
logic inputs (IN1A, IN1B, IN2A, and IN2B) states.
OUT1A, OUT1B, OUT2A, and OUT2B
These terminals provide connection to the outputs of each of
the internal H-Bridges (see
Figure 1, 17529 Simplified Internal
Block Diagram
, page 2).
VM1 and VM2
The VM terminals carry the main supply voltage and current
into the power sections of the IC. This supply then becomes
controlled and/or modulated by the IC as it delivers the power
to the loads attached between the output terminals. All VM
terminals must be connected together on the printed circuit
board.
C1L and C1H, C2L and C2H
These two pairs of terminals, the C1L and C1H and the C2L
and C2H, connect to the external bucket capacitors required by
the internal charge pump. The typical value for the bucket
capacitors is 0.1
μ
F.
C
RES
The C
RES
terminal is the output of the internal charge pump.
Its output voltage is approximately three times the V
DD
voltage.
The
VC
RES
voltage is power supply for internal predriver circuit
of H-Bridges.
PGND
Power ground terminals. They must be tied together on the
PCB.
LGND
Logic ground terminal.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC17531AR2 | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531AEL | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531AEP | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531AEV | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
| MPC17531A | 700?mA Dual H-Bridge Motor Driver with 3.0V Compatible Logic I/O |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC17529EJ | 功能描述:IC MOTOR DRIVER PAR 20TSSOP 制造商:nxp usa inc. 系列:- 包裝:管件 零件狀態:在售 電機類型 - 步進:雙極性 電機類型 - AC，DC:有刷直流 功能:驅動器 - 全集成，控制和功率級 輸出配置:半橋（4） 接口:并聯 技術:CMOS 步進分辨率:- 應用:電池供電 電流 - 輸出:700mA 電壓 - 電源:2.7 V ~ 5.6 V 電壓 - 負載:2 V ~ 6.8 V 工作溫度:-20°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 供應商器件封裝:20-TSSOP 標準包裝:75 |
| MPC17529EL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:0.7 A Dual H-Bridge Motor Driver with 3.0V/5.0V Compatible Logic I/O |
| MPC17529EP | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MPC17529EPR2 | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MPC17529EV | 功能描述:馬達/運動/點火控制器和驅動器 MPC17529 PB FREE RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。