- 您現在的位置：買賣IC網 > PDF目錄359187 > MPC17517DTBR2 (飛思卡爾半導體(中國)有限公司) 1.0 A 6.8 V Dual Motor Driver IC PDF資料下載
參數資料
| 型號： | MPC17517DTBR2 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 1.0 A 6.8 V Dual Motor Driver IC |
| 中文描述： | 1.0 6.8 V雙馬達驅動IC |
| 文件頁數： | 9/14頁 |
| 文件大小： | 163K |
| 代理商： | MPC17517DTBR2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
9
17517
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 17517 is a triple totem-pole output H-Bridge power IC
designed to drive small dc motors used in portable
electronics. The 17517 can operate efficiently with supply
voltages as low as 2.0 V to as high as 6.8 V, and provide
continuos motor drive currents of 1.0 A while handling peak
currents up to 3.0 A. It is easily interfaced to low cost MCUs
via parallel 3.0 V- or 5.0 V-compatible logic. The device can
be pulse width modulated (PWM-ed) at up to 200 kHz. The
17517 can drive two motors in two directions one at a time; or
it can drive one motor in two directions and one solenoid with
synchronous rectification of freewheeling currents one at a
time. Two-motor operation is accomplished by hooking one
motor between OUTA and OUTB, and the other motor
between OUTB and OUTC. Motor + solenoid operation is
accomplished by hooking a motor between OUTA and OUTB
and placing a solenoid between OUTC and GND.
Table 5,
Truth Table
, page
8
, describes the operating states versus
the input conditions.
As shown in
Figure 2, 17517 Simplified Internal Block
Diagram
, page
2
, the 17517 is a monolithic triple totem-pole
output bridge with built-in charge pump circuitry. Each of the
six MOSFETs forming the triple totem-pole output has an
R
DS(ON)
of
≤
0.6
(guaranteed by design). The IC has an
integrated charge pump and level shifter (for gate drive
voltages). Additionally, the IC has a built-in shoot-through
current protection circuit and undervoltage lockout function.
This IC has four operating modes: Forward, Reverse, Brake,
and Tri-Stated (High Impedance).
FUNCTIONAL PIN DESCRIPTION
DRIVER OUTPUT (OUTA, OUTB, OUTC)
These pins provide the connection to the internal power
MOSFET triple-totem-pole H-bridge of the IC.
GROUND (GND)
Power and signal ground pin.
CHARGE PUMP OUTPUT CAPACITOR (CRES)
This pin provides the connection for the external reservoir
capacitor (output of the charge pump). Alternatively, this pin
can also be used as an input to supply gate-drive voltage
from an external source via a series current-limiting resistor.
The voltage at the CRES pin will be approximately three
times the V
DD
voltage, as the internal charge pump utilizes a
voltage tripler circuit. The V
DD
RES
voltage is used by the IC to
supply gate drive for the internal power MOSFETs.
MOTOR DRIVE POWER SUPPLY (VM)
The two VM pins carry the main supply voltage and current
into the power sections of the IC. This supply then becomes
controlled and or modulated by the IC as it delivers the power
to the load attached between OUTA and OUTB.
The VM pins must be connected together on the printed
circuit board with as short as possible traces offering as low
impedance as possible between pins.
CONTROL SIGNAL INPUT AND ENABLE CONTROL
SIGNAL INPUT (IN1, IN1, EN1, EN2)
These pins are input control pins used to control the
outputs. These pins are 3.0 V/ 5.0 V CMOS-compatible
inputs with hysteresis. These pins work together to control
OUTA, OUTB, and OUTC (refer to
Table 5, Truth Table
).
CHARGE PUMP BUCKET CAPACITOR (C1L, C1H,
C2L, C2H)
These two pairs of pins, the C1L and C1H and the C2L and
C2H, connect to the external bucket capacitors required by
the internal charge pump. The typical value for the bucket
capacitors is 0.1
μ
F.
CONTROL CIRCUIT POWER SUPPLY (VDD)
This pin carries the logic supply voltage and current into
the logic sections of the IC. V
DD
has an undervoltage
threshold. If the supply voltage drops below the undervoltage
threshold, the output power stage switches to a tri-state
condition. When the supply voltage returns to a level that is
above the threshold, the power stage automatically resumes
normal operation according to the established condition of
the input pins.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC17517 | 1.0 A 6.8 V Dual Motor Driver IC |
| MPC17517DR2 | 1.0 A 6.8 V Dual Motor Driver IC |
| MPC17517DTB | 1.0 A 6.8 V Dual Motor Driver IC |
| MPC17529EVEL | 0.7 A Dual H-Bridge Motor Driver with 3.0 V/5.0 V Compatible Logic I/O |
| MPC17529 | 0.7 A Dual H-Bridge Motor Driver with 3.0V/5.0V Compatible Logic I/O(0.7 A 雙H橋電機驅動器，帶3.0V/5.0V 可兼容邏輯I/O) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC1751MTB | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:1.2 A 15 V H-Bridge Motor Driver IC |
| MPC17529 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:0.7 A Dual H-Bridge Motor Driver with 3.0V/5.0V Compatible Logic I/O |
| MPC17529EJ | 功能描述:IC MOTOR DRIVER PAR 20TSSOP 制造商:nxp usa inc. 系列:- 包裝:管件 零件狀態:在售 電機類型 - 步進:雙極性 電機類型 - AC，DC:有刷直流 功能:驅動器 - 全集成，控制和功率級 輸出配置:半橋（4） 接口:并聯 技術:CMOS 步進分辨率:- 應用:電池供電 電流 - 輸出:700mA 電壓 - 電源:2.7 V ~ 5.6 V 電壓 - 負載:2 V ~ 6.8 V 工作溫度:-20°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬）裸露焊盤 供應商器件封裝:20-TSSOP 標準包裝:75 |
| MPC17529EL | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:0.7 A Dual H-Bridge Motor Driver with 3.0V/5.0V Compatible Logic I/O |
| MPC17529EP | 功能描述:馬達/運動/點火控制器和驅動器 2CH H BRIDGES RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。