- 您現在的位置：買賣IC網 > PDF目錄371132 > MP2106DK (MONOLITHIC POWER SYSTEMS INC) 1.5A, 15V, 800KHz Synchronous Buck Converter PDF資料下載
參數資料
| 型號： | MP2106DK |
| 廠商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 1.5A, 15V, 800KHz Synchronous Buck Converter |
| 中文描述： | 3.2 A SWITCHING REGULATOR, 900 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | MO-187BA, MSOP-10 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 298K |
| 代理商： | MP2106DK |
MP2106 – 1.5A, 15V, 800KHz SYNCHRONOUS BUCK CONVERTER
MP2106 Rev. 1.6
2/22/2006
www.MonolithicPower.com
7
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2006 MPS. All Rights Reserved.
TM
voltage to ramp linearly from 0V to the desired
regulation voltage during soft-start.
The soft-start period is determined by the
equation:
5
C
45
.
t
SS
×
=
Where C5
(in nF) is the soft-start capacitor from
SS to GND, and t
SS
(in ms) is the soft-start
period. Determine the capacitor required for a
given soft-start period by the equation:
SS
t
22
.
5
C
×
=
Use values between 10nF and 22nF for C5 to
set the soft-start period (between 4ms and
10ms).
Setting the Output Voltage (see Figure 2)
Set the output voltage by selecting the resistive
voltage divider ratio. The voltage divider drops
the output voltage to the 0.895V feedback
voltage. Use 10k
for the low-side resistor of
the voltage divider. Determine the high-side
resistor by the equation:
1
R
1
V
895
.
V
2
R
OUT
×
=
Where R2 is the high-side resistor, V
OUT
is the
output voltage and R1 is the low-side resistor.
Selecting the Input Capacitor
The input current to the step-down converter is
discontinuous, and so a capacitor is required to
supply the AC current to the step-down
converter while maintaining the DC input
voltage. A low ESR capacitor is required to
keep the noise at the IC to a minimum. Ceramic
capacitors are preferred, but tantalum or low
ESR electrolytic capacitors may also suffice.
The capacitor can be electrolytic, tantalum or
ceramic. Because it absorbs the input switching
current it must have an adequate ripple current
rating. Use a capacitor with RMS current rating
greater than 1/2 of the DC load current.
For stable operation, place the input capacitor
as close to the IC as possible. A smaller high
quality 0.1μF ceramic capacitor may be placed
closer to the IC with the larger capacitor placed
further away. If using this technique, it is
recommended that the larger capacitor be a
tantalum or electrolytic type. All ceramic
capacitors should be placed close to the
MP2106. For most applications, a 10
μ
F ceramic
capacitor will work.
Selecting the Output Capacitor
The output capacitor (C2) is required to
maintain the DC output voltage. Low ESR
capacitors are preferred to keep the output
voltage ripple to a minimum. The characteristics
of the output capacitor also affect the stability of
the
regulation
control
tantalum, or low ESR electrolytic capacitors are
recommended.
system.
Ceramic,
The output voltage ripple is:
×
×
+
×
×
×
=
2
C
f
8
1
R
V
V
1
L
f
V
V
SW
ESR
IN
OUT
SW
OUT
RIPPLE
Where V
RIPPLE
is the output voltage ripple, f
SW
is
the switching frequency, V
IN
is the input voltage,
R
ESR
is the equivalent series resistance of the
output capacitors and f
SW
is the switching
frequency.
Choose an output capacitor to satisfy the output
ripple requirements of the design. A 22μF
ceramic
capacitor
is
applications.
suitable
for
most
Selecting the Inductor
The inductor is required to supply constant
current to the output load while being driven by
the switched input voltage. A larger value
inductor results in less ripple current that will
result in lower output ripple voltage. However,
the larger value inductor is likely to have a
larger
physical
size
resistance. Choose an inductor that does not
saturate under the worst-case load conditions.
A good rule for determining the inductance is to
allow the peak-to-peak ripple current to be
approximately 30% to 40% of the maximum
load current. Make sure that the peak inductor
current (the load current plus half the peak-to-
peak inductor ripple current) is below 2.5A to
prevent loss of regulation due to the current
limit.
and
higher
series
相關PDF資料 |
PDF描述 |
|---|---|
| MP2106DQ | 1.5A, 15V, 800KHz Synchronous Buck Converter |
| MP2108DK | 2A, 6V, 720KHz Synchronous Buck Converter |
| MP2108DQ | 2A, 6V, 720KHz Synchronous Buck Converter |
| MP2108 | 2A, 6V, 740KHz Synchronous Buck Converter |
| MP2108_06 | 2A, 6V, 740KHz Synchronous Buck Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP2106DK-LF-P | 功能描述:開關變換器、穩壓器與控制器 1.5A/15V Sync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP2106DK-LF-Z | 功能描述:開關變換器、穩壓器與控制器 1.5A/15V Sync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP2106DQ | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1.5A, 15V, 800KHz Synchronous Buck Converter |
| MP2106DQ-LF-P | 功能描述:開關變換器、穩壓器與控制器 1.5A/15V Sync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP2106DQ-LF-Z | 功能描述:開關變換器、穩壓器與控制器 1.5A/15V Sync Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。