參數資料
型號: MP2104DJ-1.5
廠商: MONOLITHIC POWER SYSTEMS INC
元件分類: 穩壓器
英文描述: 1.7MHz, 600mA Synchronous Step-Down Converter
中文描述: 1.4 A SWITCHING REGULATOR, 2080 kHz SWITCHING FREQ-MAX, PDSO5
封裝: 1 MM HEIGHT, MO-193AA, TSOT-23, 5 PIN
文件頁數: 9/10頁
文件大?。?/td> 454K
代理商: MP2104DJ-1.5
MP2104 – 1.7MHz 600mA SYNCHRONOUS STEP-DOWN CONVERTER
NOTICE:
MPS believes the information in this document to be accurate and reliable. However, it is subject to change without
notice. Contact MPS for current specifications. MPS encourages users of its products to ensure that third party Intellectual
Property rights are not infringed upon when integrating MPS products into any application. MPS cannot assume any legal
responsibility for any said applications.
MP2104 Rev. 1.0
10/4/05
2004 MPS, Inc.
Monolithic Power Systems, Inc.
983 University Avenue, Building A, Los Gatos, CA 95032 USA
Tel: 408-357-6600
Fax: 408-357-6601
www.MonolithicPower.com
9
TM
Input Capacitor Selection
The input capacitor reduces the surge current
drawn from the input and switching noise from
the device. The input capacitor impedance at
the switching frequency shall be less than input
source impedance to prevent high frequency
switching current passing to the input. Ceramic
capacitors with X5R or X7R dielectrics are
highly recommended because of their low ESR
and small temperature coefficients. For most
applications, a 4.7μF capacitor is sufficient.
Output Capacitor Selection
The output capacitor keeps output voltage
ripple small and ensures regulation loop stable.
The output capacitor impedance shall be low at
the switching frequency. Ceramic capacitors
with X5R or X7R dielectrics are recommended.
The output ripple
V
OUT
is approximately:
(
×
×
L
f
V
OSC
IN
)
×
×
+
×
×
3
C
f
8
1
ESR
V
V
V
V
OSC
OUT
IN
OUT
OUT
PC Board Layout
The high current paths (GND, IN and SW)
should be placed very close to the device with
short, direct and wide traces. Input capacitor C1
needs to be as close as possible to the IN and
GND pins. The external feedback resistors shall
be placed next to the FB pin. Keep the
switching node SW short and away from the
feedback network. Figure 3 illustrates an
example of PCB layout and signal routing.
Figure 3—MP2104 Suggested Layout
For the fixed output versions (MP2104DJ-1.5
and MP2104-1.8), R1 is shorted and R2 is
open.
MP2104
SW
FB
EN
GND
IN
OUTPUT
1.8V
600mA
INPUT
2.5V - 6V
MP2104_F04
OFF ON
3
5
2
1
4
100
90
80
70
60
50
40
30
20
10
0
E
10
100
1000
LOAD CURRENT (mA)
MP2104-EC02
Efficiency vs
Load Current
V
IN
= 3.3V
V
IN
= 4.2V
Figure 4—V
IN
= 2.5V to 6V, V
OUT
= 1.8V, I
LOAD
= 600mA Step-Down Circuit
(L = 10μH for Higher Light-Load Efficiency)
相關PDF資料
PDF描述
MP2104DJ-1.8 1.7MHz, 600mA Synchronous Step-Down Converter
MP2105_06 1MHz, 800mA Synchronous Step-Down Converter
MP2105 1MHz, 800mA Synchronous Step-Down Converter
MP2105DJ 1MHz, 800mA Synchronous Step-Down Converter
MP2106 1.5A, 15V, 800KHz Synchronous Buck Converter
相關代理商/技術參數
參數描述
MP2104DJ-LF-P 功能描述:開關變換器、穩壓器與控制器 0.6A/6V Synch Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MP2104DJ-LF-Z 功能描述:開關變換器、穩壓器與控制器 0.6A/6V Synch Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MP2104DQT-LF-P 功能描述:開關變換器、穩壓器與控制器 0.6A/6V Synch Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MP2104DQT-LF-Z 功能描述:開關變換器、穩壓器與控制器 0.6A/6V Synch Step-Down RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel
MP2105 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1MHz 800mA synchronous Step-Down converter