參數資料
型號: MP1543
廠商: Monolithic Power Systems, Inc.
英文描述: 1.5A, 500KHz Synchronous Rectified Step-up Converter
中文描述: 1.5A的,500KHz的同步整流升壓轉換器
文件頁數: 6/9頁
文件大?。?/td> 299K
代理商: MP1543
MP1543 — 1.5A, 500KHZ SYNCHRONOUS RECTIFIED STEP-UP CONVERTER
MP1543 Rev. 1.0
1/11/2006
www.MonolithicPower.com
6
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2006 MPS. All Rights Reserved.
TM
APPLICATION INFORMATION
COMPONENT SELECTION
Setting the Output Voltage
Set the output voltage by selecting the resistive
voltage divider ratio. The voltage divider drops
the output voltage to the 1.2V feedback voltage.
Use a 100k
resistor for R2 of the voltage
divider. Determine the high-side resistor R1 by
the equation:
=
2
R
V
V
V
1
R
FB
FB
OUT
Where V
OUT
is the output voltage, V
FB
is the
1.2V feedback voltage and R2=100k
.
Selecting the Input Capacitor
An input capacitor is required to supply the AC
ripple current to the inductor, while limiting noise
at
the
input
source.
capacitors are the best choice as they have
extremely low ESR and are available in small
footprints. Use an input capacitor value of 4.7μF
or greater. This capacitor must be placed
physically close to the device.
Multi-layer
ceramic
Selecting the Output Capacitor
A single 4.7
μ
F to 10
μ
F ceramic capacitor
usually provides sufficient output capacitance
for most applications. Larger values up to 22
μ
F
may be used to obtain extremely low output
voltage ripple and improve transient response.
The impedance of the ceramic capacitor at the
switching frequency is dominated by the
capacitance, and so the output voltage ripple is
mostly independent of the ESR. The output
voltage ripple V
RIPPLE
is calculated as:
(
)
SW
UT
O
IN
UT
2
C
O
LOAD
V
RIPPLE
V
f
V
V
×
I
×
=
Where V
IN
is the input voltage, I
LOAD
is the load
current, C2 is the capacitance of the output
capacitor and f
SW
is the 500KHz switching
frequency.
Selecting the Inductor
The inductor is required to force the output
voltage higher while being driven by the lower
input voltage. A good rule for determining the
inductance is to allow the peak-to-peak ripple
current to be approximately 30%-50% of the
maximum input current. Make sure that the
peak inductor current is below the minimum
current limit at the duty cycle used (to prevent
loss of regulation due to the current limit
variations).
Calculate the required inductance value L using
the equations:
I
f
V
)
V
×
-
(V
V
L
SW
OUT
IN
OUT
×
IN
×
=
η
×
)
I
×
=
IN
)
MAX
(
LOAD
I
OUT
V
)
MAX
(
IN
I
V
(
)
MAX
(
IN
%
50
%
30
I
=
Where I
LOAD(MAX)
is the maximum load current,
I
is the peak-to-peak inductor ripple current and
η
is efficiency. For the MP1543, typically, 4.7
μ
H is
recommended for most applications. Choose an
inductor that does not saturate at the peak
switch current as calculated above with
additional margin to cover heavy load transients
and extreme startup conditions.
相關PDF資料
PDF描述
MP1543DJ 1.5A, 500KHz Synchronous Rectified Step-up Converter
MP1567 1.2A Synchronous Rectified Step-Down Converter
MP1567DK 1.2A Synchronous Rectified Step-Down Converter
MP1567DQ 1.2A Synchronous Rectified Step-Down Converter
MP1570DN 3A, 23V, 340KHz Synchronous Rectified Step-Down Converter
相關代理商/技術參數
參數描述
MP1543DJ 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1.5A, 500KHz Synchronous Rectified Step-up Converter
MP1546A 制造商:Motorola Inc 功能描述:ELECTRONIC COMPONENT
MP154-BP 制造商:Micro Commercial Components (MCC) 功能描述:Diode Rectifier Bridge Single 400V 15A 4-Pin MP-50 Bulk
MP154W 功能描述:橋式整流器 15A 400V LP RoHS:否 制造商:Vishay 產品:Single Phase Bridge 峰值反向電壓:1000 V 最大 RMS 反向電壓: 正向連續電流:4.5 A 最大浪涌電流:450 A 正向電壓下降:1 V 最大反向漏泄電流:10 uA 功率耗散: 最大工作溫度:+ 150 C 長度:30.3 mm 寬度:4.1 mm 高度:20.3 mm 安裝風格:Through Hole 封裝 / 箱體:SIP-4 封裝:Tube
MP155 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:Energy Efficient Off-line Regulator