- 您現在的位置：買賣IC網 > PDF目錄371132 > MP1542DH (MONOLITHIC POWER SYSTEMS INC) 700KHz/1.3MHz Boost Converter with a 2A Switch PDF資料下載
參數資料
| 型號： | MP1542DH |
| 廠商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 700KHz/1.3MHz Boost Converter with a 2A Switch |
| 中文描述： | 2 A SWITCHING REGULATOR, 1500 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | MO-187AA-T, MSOP-8 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 491K |
| 代理商： | MP1542DH |
MP1542 – 700KHz/1.3MHz BOOST CONVERTER WITH A 2A SWITCH
MP1542 Rev. 1.2
12/14/2005
www.MonolithicPower.com
6
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2005 MPS. All Rights Reserved.
At the beginning of each cycle, the N-Channel
MOSFET switch is turned on, forcing the
inductor current to rise. The current at the
source of the switch is internally measured and
converted to a voltage by the current sense
amplifier. That voltage is compared to the error
voltage at COMP. The voltage at the output of
the error amplifier is an amplified version of the
difference between the 1.25V reference voltage
and the feedback voltage. When these two
voltages are equal, the PWM comparator turns
off the switch forcing the inductor current to the
output capacitor through the external rectifier.
This causes the inductor current to decrease.
The peak inductor current is controlled by the
voltage at COMP, which in turn is controlled by
the output voltage. Thus the output voltage
controls the inductor current to satisfy the load.
The use of current mode regulation improves
transient response and control loop stability.
APPLICATION INFORMATION
Components referenced below apply to Typical Application Circuit on page 1.
Selecting the Soft-Start Capacitor
The MP1542 includes a soft-start timer that
limits the voltage at COMP during startup to
prevent excessive current at the input. This
prevents premature termination of the source
voltage at startup due to input current
overshoot. When power is applied to the
MP1542, and enable is asserted, a 6μA internal
current source charges the external capacitor at
SS. As the SS capacitor is charged, the voltage
at SS rises. The MP1542 internally clamps the
voltage at COMP to 700mV above the voltage
at SS. The soft-start ends when the voltage at
SS reaches 0.45V. This limits the inductor
current at start-up, forcing the input current to
rise slowly to the current required to regulate
the output voltage.
The soft-start period is determined by the
equation:
SS
SS
C
7
t
×
=
Where C
SS
(in nF) is the soft-start capacitor
from SS to GND, and t
SS
(in
μ
s) is the soft-start
period.
Determine the capacitor required for a given
soft-start period by the equation:
SS
SS
t
×
0133
.
C
=
Setting the Output Voltage
Set the output voltage by selecting the resistive
voltage divider ratio. Use 10k
for the low-side
resistor R2 of the voltage divider. Determine the
high-side resistor R1 by the equation:
FB
FB
OUT
V
)
V
V
(
R
1
R
=
where V
OUT
is the output voltage.
For R2 = 10k
and V
FB
= 1.25V, then
R1 (k
) = 8k
(V
OUT
– 1.25V).
Selecting the Input Capacitor
An input capacitor is required to supply the AC
ripple current to the inductor, while limiting
noise at the input source. A low ESR capacitor
is required to keep the noise at the IC to a
minimum. Ceramic capacitors are preferred, but
tantalum or low-ESR electrolytic capacitors may
also suffice.
Use an input capacitor value greater than
4.7μF. The capacitor can be electrolytic,
tantalum or ceramic. However since it absorbs
the input switching current it requires an
adequate ripple current rating. Use a capacitor
with RMS current rating greater than the
inductor ripple current (see Selecting The
Inductor to determine the inductor ripple
current).
To insure stable operation place the input
capacitor as close to the IC as possible.
Alternately a smaller high quality ceramic 0.1μF
capacitor may be placed closer to the IC with
the larger capacitor placed further away. If
using this technique, it is recommended that the
larger capacitor be a tantalum or electrolytic
type. All ceramic capacitors should be placed
close to the MP1542.
相關PDF資料 |
PDF描述 |
|---|---|
| MP1542DK | 700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1542 | 700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1542_06 | 700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1543 | 1.5A, 500KHz Synchronous Rectified Step-up Converter |
| MP1543DJ | 1.5A, 500KHz Synchronous Rectified Step-up Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP1542DK | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1542DK-LF-P | 功能描述:開關變換器、穩壓器與控制器 .7/1.3MHz 22Vout Step-up Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP1542DK-LF-Z | 功能描述:開關變換器、穩壓器與控制器 .7/1.3MHz 22Vout Step-up Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP1543 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1.5A, 500KHz Synchronous Rectified Step-up Converter |
| MP1543DJ | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1.5A, 500KHz Synchronous Rectified Step-up Converter |
發布緊急采購，3分鐘左右您將得到回復。