- 您現在的位置：買賣IC網 > PDF目錄371132 > MP1541_06 (Monolithic Power Systems, Inc.) 1.3MHz Boost Converter PDF資料下載
參數資料
| 型號： | MP1541_06 |
| 廠商： | Monolithic Power Systems, Inc. |
| 英文描述： | 1.3MHz Boost Converter |
| 中文描述： | 1.3MHz升壓轉換器 |
| 文件頁數： | 4/8頁 |
| 文件大?。?/td> | 322K |
| 代理商： | MP1541_06 |
MP1541 – 1.3MHZ BOOST CONVERTER
MP1541Rev.1.2
3/20/2006
www.MonolithicPower.com
4
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2006 MPS. All Rights Reserved.
PIN FUNCTIONS
Pin # Name Function
1
SW
Power Switch Output. SW is the drain of the internal MOSFET switch. Connect the power
inductor and output rectifier to SW. SW can swing between GND and 22V.
2
GND Ground.
3
FB
Feedback Input. FB voltage is 1.25V. Connect a resistor divider to FB.
4
EN
Regulator On/Off Control Input. A high input at EN turns on the converter, and a low input turns
it off. When not used, connect EN to the input source for automatic startup.
The EN pin cannot
be left floating.
5
IN
Input Supply Pin. Must be locally bypassed.
OPERATION
The MP1541 uses a fixed frequency, peak current
mode boost regulator architecture to regulate
voltage at the feedback pin. The operation of the
MP1541 can be understood by referring to the
block diagram of Figure 1. At the start of each
oscillator cycle the MOSFET is turned on through
the control circuitry. To prevent sub-harmonic
oscillations at duty cycles greater than 50 percent,
a stabilizing ramp is added to the output of the
current sense amplifier and the result is fed into
the negative input of the PWM comparator. When
this voltage equals the output voltage of the error
amplifier the power MOSFET is turned off. The
voltage at the output of the error amplifier is an
R
C
amplified version of the difference between the
1.25V bandgap reference voltage and the
feedback voltage. In this way the peak current
level keeps the output in regulation. If the
feedback voltage starts to drop, the output of the
error amplifier increases. This results in more
current to flow through the power MOSFET, thus
increasing the power delivered to the output.
The MP1541 has internal soft start to limit the
amount of input current at startup and to also
limit the amount of overshoot on the output. The
current limit is increased by a fourth every 40
μ
s
giving a total soft start time of 120
μ
s.
PWM
COMPARATOR
ERROR
AMPLIFIER
C
C
CONTROL
LOGIC
CURRENT
SENSE
AMPLIFIER
SW
1
M1
GND
+
-
FB
3
2
1.3MHz
OSC
+
-
-
+
+
1.25V
MP1541-F01-BD01
Figure 1—Functional Block Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| MP1541DJ | MP1541 TFT Applications Evaluation Board |
| MP1541 | 1.3MHz Low Power LED Torch/Flash Driver |
| MP1542DH | 700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1542DK | 700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1542 | 700KHz/1.3MHz Boost Converter with a 2A Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP1541DJ | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1.3MHz Boost Converter |
| MP1541DJ-LF-P | 功能描述:開關變換器、穩壓器與控制器 1.3MHz, 22V Step-up Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP1541DJ-LF-Z | 功能描述:開關變換器、穩壓器與控制器 1.3MHz, 22V Step-up Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP1542 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:700KHz/1.3MHz Boost Converter with a 2A Switch |
| MP1542_06 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:700KHz/1.3MHz Boost Converter with a 2A Switch |
發布緊急采購，3分鐘左右您將得到回復。