- 您現在的位置：買賣IC網 > PDF目錄371131 > MP1529DR (MONOLITHIC POWER SYSTEMS INC) Fixed Frequency Step-Up Converter LCD Backlight Plus Flash Evaluation Board PDF資料下載
參數資料
| 型號： | MP1529DR |
| 廠商： | MONOLITHIC POWER SYSTEMS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Fixed Frequency Step-Up Converter LCD Backlight Plus Flash Evaluation Board |
| 中文描述： | 1.2 A SWITCHING REGULATOR, 1400 kHz SWITCHING FREQ-MAX, QCC16 |
| 封裝： | 4 X 4 MM, QFN-16 |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 206K |
| 代理商： | MP1529DR |
EV1529DR-00A – FIXED FREQUENCY CONVERTER LCD BACKLIGHT EV BOARD
NOTICE:
The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
EV1529DR-00A Rev. 1.0
11/2/2005
www.MonolithicPower.com
4
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2005 MPS. All Rights Reserved.
TM
QUICK START GUIDE
The LED currents at backlight mode, backlight plus review mode and flash mode are set to 20mA, 40mA, and
100mA, respectively on this board. The board layout accommodates mostly common used inductors and
output capacitors.
1. Preset Power Supply to 2.7V
≤
V
IN
≤
4.2V.
2. Turn Power Supply off.
3. Connect Power Supply terminals to:
a. Positive (+): VIN
b. Negative (–): GND
4. Solder the first backlight LED string to LED1 - LED4.
Solder the second backlight LED string to LED5 – LED8.
Solder the flash LED string to LED9 – LED12.
Set EN1 and EN2 based on the Enable Operation Table below. Connect EN1, EN2 to VIN to set
them “H” and to GND to set them “L”.
Mode
EN1
EN2
Strings 1+2: LCD
Backlight LEDs
Off
On (PWM)
On (PWM)
Off
String 3: Flash
LEDs
Off
Off
Preview current
Flash current
Off
L
L
L
H
H
Backlight
H (PWM)
H (PWM)
L
Backlight plus Preview
Flash
5. Turn Power Supply on after making connections.
The LED currents can be adjusted by changing the values of resistors RS1, RS2, and RS3. V
SET
= 1.216V.
BL
_
LED
SET
V
I
950
1
RS
×
=
PV
_
LED
SET
V
I
1100
2
RS
×
=
FL
_
LED
SET
V
I
1000
3
RS
×
=
For examples, If I
LED_BL
= 10mA, then
=
×
10
=
k
52
.
115
216
.
950
1
RS
(Use a 115k
1% resistor)
If I
LED_PL
= 20mA, then
=
×
20
=
k
88
.
66
216
.
1100
2
RS
(Use a 66.5k
1% resistor)
If I
LED_FL
= 150mA, then
=
×
=
k
11
.
150
216
.
1000
3
RS
(Use a 8.06k
1% resistor)
相關PDF資料 |
PDF描述 |
|---|---|
| MP1529 | Fixed Frequency Step-Up Converter LCD Backlight Plus Flash |
| MP1530DM | Triple Output Step-Up Plus Linear Regulators for TFT Bias |
| MP1530DQ | Triple Output Step-Up Plus Charge Pump for TFT Bias |
| MP1530 | Triple Output TFT Bias Converter |
| MP1531DQ | Low Power, Triple Output Step-Up Plus Charge Pump for TFT Bias |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP1529DR-LF-P | 功能描述:LED照明驅動器 2x6 backlight 1x4 flash WLED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MP1529DR-LF-Z | 功能描述:LED照明驅動器 2x6 backlight 1x4 flash WLED Driver RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MP152-BP | 制造商:Micro Commercial Components (MCC) 功能描述:Diode Rectifier Bridge Single 200V 15A 4-Pin MP-50 Bulk |
| MP152W | 功能描述:橋式整流器 15A 200V LP RoHS:否 制造商:Vishay 產品:Single Phase Bridge 峰值反向電壓:1000 V 最大 RMS 反向電壓: 正向連續電流:4.5 A 最大浪涌電流:450 A 正向電壓下降:1 V 最大反向漏泄電流:10 uA 功率耗散: 最大工作溫度:+ 150 C 長度:30.3 mm 寬度:4.1 mm 高度:20.3 mm 安裝風格:Through Hole 封裝 / 箱體:SIP-4 封裝:Tube |
| MP1530 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:Triple Output Step-Up Plus Linear Regulators for TFT Bias |
發布緊急采購，3分鐘左右您將得到回復。