- 您現在的位置：買賣IC網 > PDF目錄371131 > MP1521 (Monolithic Power Systems, Inc.) High Efficiency White LED Driver PDF資料下載
參數資料
| 型號： | MP1521 |
| 廠商： | Monolithic Power Systems, Inc. |
| 元件分類： | LED驅動器 |
| 英文描述： | High Efficiency White LED Driver |
| 中文描述： | 高效率白光LED驅動器 |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 175K |
| 代理商： | MP1521 |
MP1521
High Efficiency
White LED Driver
Functional Description
Operation
MP1521 Rev 2.7 10/06/04
www.monolithicpower.com
5
Monolithic Power Systems
The MP1521 utilizes a constant off-time
control scheme (Refer to the Block
Diagram). For maximum brightness, the
BRT pin is biased at or above 1.2V. Its
voltage is routed through the unity gain
buffer whose the output of is clamped at
1.2V. A 20K/10K divider from the Buffer to
the non-inverting input of the Feedback
comparator divides the BRT voltage by
three to set the current sense threshold. If
any of the feedback pins FB1, FB2, or FB3
is lower than this threshold the Power FET
is turned on. The Power MOSFET and
inductor current increases until the current
limit comparator trips at 0.5A turning off the
MOSFET for 500ns. At the end of 500ns if
any of the Feedback pins are still lower
than the current sense threshold. The
Power FET is again turned on. This cycle
repeats itself until all three of the feedback
pins exceed the threshold.
Analog Brightness Adjust
Analog Brightness Adjust is accomplished
by applying a voltage between 0.26V to
1.2V on the BRT pin. The 1.23V REF
output can be used to bias a potentiometer
whose wiper drives the BRT pin.
PWM/ Brightness Adjust
PWM Brightness Adjust is accomplished
by driving the BRT pin with a square wave
whose low voltage is below 0.2V and
whose high voltage is greater than 1.2V. A
voltage below 0.2V forces the Power
MOSFET off. A voltage greater than 1.2V
will cause all three feedback pins to
regulate at or above 0.4V
Open Load Shut-Off
Open Load Shut-Off is implemented by
connecting the OLS pin to V
OUT
. In the
fault condition where the connection to the
LED’s is open, V
OUT
will rise up, as all the
feedback pins are absent of voltage. Once
V
OUT
exceeds 28V, the part will cease
operation until the EN pin is cycled off and
on. To disable the open load shut-off
feature, connect the OLS pin to GND.
相關PDF資料 |
PDF描述 |
|---|---|
| MP1522_06 | 25V Step-Up Converter in a SOT23-5 Package |
| MP1522ET | 25V Step-Up Converter in a SOT23-5 Package |
| MP1522EQ | 25V Step-Up Converter in a SOT23-5 Package |
| MP1522 | Precision 6 White LED Driver Evaluation Board |
| MP1522DT | Precision 6 White LED Driver Evaluation Board |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP1521_R2.7W | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:High Efficiency White LED Driver |
| MP1521EK | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:High Efficiency White LED Driver |
| MP1521EK-LF | 制造商:Monolithic Power Systems 功能描述:15 LED, 2.5 - 25Vin Switch Driver |
| MP1521EK-LF-P | 功能描述:電源開關 IC - 配電 15 LED, 2.5 - 25Vin Switch Driver RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| MP1521EK-LF-Z | 功能描述:電源開關 IC - 配電 15 LED, 2.5 - 25Vin Switch Driver RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
發布緊急采購，3分鐘左右您將得到回復。