- 您現在的位置：買賣IC網 > PDF目錄371131 > MP1517 (Monolithic Power Systems, Inc.) 3A, 25V, 1.1MHz Step-Up Converter PDF資料下載
參數資料
| 型號： | MP1517 |
| 廠商： | Monolithic Power Systems, Inc. |
| 英文描述： | 3A, 25V, 1.1MHz Step-Up Converter |
| 中文描述： | 第3A，25V的，為1.1MHz升壓轉換器 |
| 文件頁數： | 9/13頁 |
| 文件大?。?/td> | 323K |
| 代理商： | MP1517 |
MP1517 – 3A, 25V, 1.1MHz STEP-UP CONVERTER
MP1517 Rev. 1.4
4/28/2006
www.MonolithicPower.com
9
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2006 MPS. All Rights Reserved.
Selecting the Output Diode
The output diode is typically a Schottky diode.
The Schottky diode is selected based upon
voltage requirement, current rating, and thermal
capability. The diode breakdown and power
switch breakdown voltage are set higher than
V
OUT
+ V
IN
, since this is the voltage stress on
both of these devices. The current rating is set
based on the average load current in the diode.
The average diode current is equal to the load
current, but the peak current and power
consumption on D1 is:
IN
D
IN
LOAD
)
PEAK
(
D
V
V
V
I
2
I
I
+
×
+
=
D
LOAD
1
D
V
I
P
×
=
Selecting the Coupling Capacitor
The steady state voltage across L1 and L2 is
equal to zero. Therefore the coupling capacitor
has V
IN
across it in steady state. The coupling
capacitor will need to be rated for an input
voltage plus some guard band. Also this
capacitor will need an I
RMS
ripple current rating:
IN
D
OUT
LOAD
)
RMS
(
8
C
V
V
V
I
I
+
×
=
Application Examples
Figure 2 shows a typical application circuit
driving multiple strings of LEDs with the
MP1517. The 3 strings of 6 white LEDs can be
driven from a voltage supply range of 2.6V to
6V at an output current of 20mA. A 1μF output
capacitor is usually sufficient for this kind of
application. A 4.7μH inductor with low DCR
(inductor resistance) is recommended to
improve efficiency. A 10μF ceramic capacitor is
recommended for the input capacitance.
Schottky diodes have fast recovery and a low
forward voltage and are recommended. The
MP1517 soft-start helps to limit the amount of
current through V
IN
at startup and to also limit
the amount of overshoot on the output.
Figure 3 shows a typical application running the
MP1517 in flash mode. During preview mode,
resistor R2 sets the current through the white
LEDs to 20mA. When a flash is required the
N-Channel MOSFET Q1 is turned on and
150mA
flows
through
compensation capacitor has been increased to
47nF. This forces the compensation node to
slowly rise when Q1 is turned on which allows
the current through the inductor to slowly
increase without overshoot. By doing this the
inrush current on the input is minimized.
the
LEDs.
The
Figure 4 shows a SEPIC circuit using the
MP1517 to generate 3.3V output from a 3V to
4.2V input. A peak voltage detect circuit (D2
and C7) is added to the IN pin from the highest
voltage potential (SW node) in the entire circuit.
The average voltage on C7 is roughly the sum
of V
IN
and V
OUT
. This ensures the enhancement
of the internal MOSFET switch. A transformer
with two windings can be used to replace the
two separate inductors in Figure 4. In this case,
the effective inductance value is doubled due to
the mutual inductance of each winding. This
reduces the inductor ripple current and
improves efficiency. Figures 5 and 6 show
some other SEPIC application circuits.
Layout Consideration
High frequency switching regulators require
very careful layout for stable operation and low
noise. All components must be placed as close
to the IC as possible. Keep the path between
L1, D1, and C2 (also L2, C8 if applicable)
extremely short for minimal noise and ringing.
C1 must be placed close to the IN pin for best
decoupling. All feedback components must be
kept close to the FB pin to prevent noise
injection on the FB pin trace. The ground return
of C1 and C2 should be tied close to the PGND
pins. See the MP1517 demo board layout for
reference.
相關PDF資料 |
PDF描述 |
|---|---|
| MP1518DG | Fixed Frequency WLED Driver Evaluation Board |
| MP1528DQ | 9 Lamp, 20mA Preciscion WLED Driver Evaluation Board |
| MP1518DJ | Fixed Frequency White LED Driver |
| MP1518 | Fixed Frequency White LED Driver |
| MP1518DJE | Fixed Frequency White LED Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MP1517DR | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:3A, 25V, 1.1MHz Step-Up Converter |
| MP1517DR-LF-P | 功能描述:開關變換器、穩壓器與控制器 3A Switch / 25Vout Step-Up Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP1517DR-LF-Z | 功能描述:開關變換器、穩壓器與控制器 3A Switch / 25Vout Step-Up Converter RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| MP1518 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:Fixed Frequency White LED Driver |
| MP1518DG | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:Fixed Frequency White LED Driver |
發布緊急采購，3分鐘左右您將得到回復。