- 您現在的位置：買賣IC網 > PDF目錄45334 > MM908E626AVEK (FREESCALE SEMICONDUCTOR INC) FLASH, 32 MHz, MICROCONTROLLER, PDSO54 PDF資料下載
參數資料
| 型號： | MM908E626AVEK |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | FLASH, 32 MHz, MICROCONTROLLER, PDSO54 |
| 封裝： | 5.10 X 10.30 MM, 0.65 MM PITCH, LEAD FREE, SOIC-54 |
| 文件頁數： | 26/43頁 |
| 文件大?。?/td> | 842K |
| 代理商： | MM908E626AVEK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
Analog Integrated Circuit Device Data
32
Freescale Semiconductor
908E626
TYPICAL APPLICATIONS
TYPICAL APPLICATIONS
DEVELOPMENT SUPPORT
As the 908E626 has the MC68HC908EY16 MCU
embedded, typically all the development tools available for
the MCU also apply for this device. However, due to the fact
of the additional analog die circuitry and the nominal +12 V
supply voltage some additional items have to be considered:
nominal 12 V rather than 5.0 V or 3.0 V supply
high voltage VTST might be applied not only to IRQ pin,
but also the IRQ_A pin
For a detailed information on the MCU related
development support, see the MC68HC908EY16 datasheet -
section, development support.
The programming is principally possible at two stages in
the manufacturing process - first on chip level, before the IC
is soldered onto a pcb board, and second, after the IC is
soldered onto the pc board.
Chip level programming
At the Chip level, the easiest way is to only power the MCU
with +5.0 V (see Figure 16), and not provide the analog chip
with VSUP. In this setup, all the analog pins should be left
open (e.g. VSUP[1:3]), and interconnections between the
MCU and the analog die have to be separated (e.g. IRQ -
IRQ_A
).
This mode is well described in the MC68HC908EY16
datasheet - section, development support.
Figure 16. Normal Monitor Mode Circuit (MCU only)
It is also possible to supply the whole system with VSUP
(12 V) instead as described in Figure 17.
PCB level programming
If the IC is soldered onto the pc board, it is typically not
possible to separately power the MCU with +5.0 V. The
whole system has to be powered up providing VSUP (see
MM908E626
RST_A
RST
IRQ_A
IRQ
VSUP[1:3]
GND[1:2]
PTC4/OSC1
PTB3/AD3
PTB4/AD4
PTA0/KBD0
PTA1/KBD1
MAX232
10k
RS232
DB-9
1
3
C1+
C1-
4
5
C2+
C2-
7
8
2
3
5
VCC
GND
16
15
2
V+
V-
6
1F
+
1F
+
1F
+
1F
2
1
3
65
4
74HC125
9.8304MHz CLOCK
+5V
DATA
CLK
+5V
10k
VTST
10
9
T2OUT
R2IN
T2IN
R2OUT
EVDD
VDD
VSS
4.7F
100nF
+5V
VREFL
VDDA
EVSS
VREFH
VSSA
相關PDF資料 |
PDF描述 |
|---|---|
| MMAD1108R2 | 0.4 A, 8 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD1504A-TP | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD1505A-TP | 0.2 A, 2 ELEMENT, SILICON, SIGNAL DIODE |
| MMBD2837LT3 | 0.15 A, 2 ELEMENT, SILICON, SIGNAL DIODE, TO-236AB |
| MMBZ27VCL/DG | TVS DIODE, TO-236AB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626AVPEKR2 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM-90N | 功能描述:ANT MAGN MNT VEHIC 3.5"DIA 10'NF RoHS:是 類別:RF/IF 和 RFID >> RF 天線 系列:* 標準包裝:1 系列:* |
| MM90R9F | 制造商:Ohmite Mfg Co 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。