- 您現在的位置：買賣IC網 > PDF目錄1954 > MM908E626AVDWB (Freescale Semiconductor)IC STEPPER MOTOR DRIVER 54-SOIC PDF資料下載
參數資料
| 型號： | MM908E626AVDWB |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 22/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC STEPPER MOTOR DRIVER 54-SOIC |
| 標準包裝： | 26 |
| 應用： | 自動鏡像控制 |
| 核心處理器： | HC08 |
| 程序存儲器類型： | 閃存（16 kB） |
| 控制器系列： | 908E |
| RAM 容量： | 512 x 8 |
| 接口： | SCI，SPI |
| 輸入/輸出數： | 13 |
| 電源電壓： | 8 V ~ 18 V |
| 工作溫度： | -40°C ~ 115°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 54-BSSOP（0.295"，7.50mm 寬）裸露焊盤 |
| 包裝： | 管件 |
| 供應商設備封裝： | 54-SOICW-EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
29
908E626
FUNCTIONAL DEVICE OPERATION
OPERATIONAL MODES
1 = Current sense amplification set for measuring 0.5 A.
0 = Current sense amplification set for measuring 2.5 A.
CLS2:CLS0—H-Bridge Current Limitation Selection Bits
These read/write bits select the current limitation value
according to Table 8. Reset clears the CLS2:CLS0 bits.
Switchable VDD Outputs
The HVDD pin is a switchable VDD output pin. It can be
used for driving external circuitry that requires a VDD voltage.
The output is enabled with bit PSON in the System Control
Register and can be switched on/off with bit HVDDON in the
Power Output Register. Low or high voltage conditions (LVI/
HVI) have no influence on this circuitry.
HVDD Overtemperature Protection
Overtemperature protection is enabled if the high
temperature reset is enabled.
HVDD Overcurrent Protection
The HVDD output is protected against overcurrent. In the
event the overcurrent limit is or was reached, the output
automatically switches off and the HVDD overcurrent flag in
the System Status Register is set.
System Control Register (SYSCTL)
PSON—Power Stages On Bit
This read/write bit enables the power stages (half-bridges,
LIN transmitter and HVDD output). Reset clears the PSON
bit.
1 = Power stages enabled.
0 = Power stages disabled.
SRS0:SRS1—LIN Slew Rate Selection Bits
These read/write bits enable the user to select the
appropriate LIN slew rate for different baud rate
configurations as shown in Table 9.
The high speed slew rates are used, for example, for
programming via the LIN and are not intended for use in the
application.
Go to STOP Mode Bit (GS)
This write-only bit instructs the 908E626 to power down
and go into STOP mode. Reset or CPU interrupt requests
clear the GS bit.
1 = Power down and go into STOP mode
0 = Not in STOP mode
System Status Register (SYSSTAT)
LINCL — LIN Current Limitation Bit
This read-only bit is set if the LIN transmitter operates in
current limitation region. Due to excessive power dissipation
in the transmitter, software is advised to turn the transmitter
off immediately.
1 = Transmitter operating in current limitation region.
0 = Transmitter not operating in current limitation
region.
HVDD_OCF—HVDD Output Overcurrent Flag Bit
This read/write flag is set on an overcurrent condition at
the HVDD pin. Clear HVDD_OCF and enable the output by
writing a logic [1] to the HVDD_OCF Flag. Reset clears the
Table 8. H-Bridge Current Limitation Value Selection
Bits
CLS2
CLS1
CLS0
Current Limit
000
No Limit
001
010
011
55 mA (typ)
100
260 mA (typ)
101
370 mA (typ)
110
550 mA (typ)
111
740 mA (typ)
Register Name and Address: SYSCTL - $03
Bit7
6
5
4
3
2
1
Bit0
Read
PSON
SRS1
SRS0
0
Write
GS
Reset
0
0000
0
Table 9. LIN Slew Rate Selection Bits
SRS1
SRS0
LIN Slew Rate
0
Initial Slew Rate (20 kBaud)
0
1
Slow Slew Rate (10 kBaud)
1
0
High Speed II (8x)
1
High Speed I (4x)
Register Name and Address: SYSSTAT - $0c
Bit7
6
5
4
3
2
1
Bit0
Read
0
LINCL HVDD
_OCF
0
LVF
HVF
HB_
OCF
HTF
Write
Reset
0000
相關PDF資料 |
PDF描述 |
|---|---|
| MM912F634BV1AER2 | IC MCU 16BIT 32KB FLASH 48LQFP |
| MM912H634CM1AER2 | IC 64KS12 LIN2XLS/HS ISENSE |
| MMC2001HCAB33B | IC MCU 32BIT 33MHZ 144-LQFP |
| MMC2107CFCPU33 | IC MCU 32BIT 33MHZ 100-LQFP |
| MMC2114CFCAG33 | IC MCU 32BIT 33MHZ 144-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MM908E626AVDWB/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
| MM908E626AVEK | 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| MM908E626AVPEK | 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626AVPEKR2 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| MM908E626R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication |
發布緊急采購，3分鐘左右您將得到回復。