參數資料
型號： MM908E626
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： 基準電壓源/電流源
英文描述： Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
中文描述： 集成的步進電機驅動器，帶有嵌入式微控制器和LIN串行通信
文件頁數： 28/38頁
文件大?。?/td> 507K
代理商： MM908E626
Analog Integrated Circuit Device Data
Freescale Semiconductor
28
908E626
FUNCTIONAL DEVICE OPERATION
LOGIC COMMANDS AND REGISTERS
HVDD_OCF — HVDD Output Overcurrent Flag Bit
This read / write flag is set on an overcurrent condition at
the HVDD terminal. Clear HVDD_OCF and enable the output
by writing a logic [1] to the HVDD_OCF Flag. Reset clears the
HVDD_OCF bit. Writing a logic [0] to HVDD_OCF has no
effect.
1 = Overcurrent condition on HVDD has occurred.
0 = No overcurrent condition on HVDD has occurred.
LVF —
Low-Voltage Bit
This read only bit is a copy of the LVF bit in the Interrupt
Flag Register.
1 = Low-voltage condition has occurred.
0 = No low-voltage condition has occurred.
HVF —
High-Voltage Sensor Bit
This read-only bit is a copy of the HVF bit in the Interrupt
Flag Register.
1 = High-voltage condition has occurred.
0 = No high-voltage condition has occurred.
HB_OCF — H-Bridge Overcurrent Flag Bit
This read write flag is set on an overcurrent condition at
the H-Bridges. Clear HB_OCF and enable the H-Bridge
driver by writing a logic [1] to HB_OCF. Reset clears the
HB_OCF bit. Writing a logic [0] to HB_OCF has no effect.
1 = Overcurrent condition on H-Bridges has occurred.
0 = No overcurrent condition on H-Bridges has
occurred.
HTF — Overtemperature Status Bit
This read-only bit is a copy of the HTF bit in the Interrupt
Flag Register.
1 = Overtemperature condition has occurred.
0 = No overtemperature condition has occurred.
AUTONOMOUS WATCHDOG (AWD)
The Autonomous Watchdog module allows to protect the
CPU against code runaways.
The AWD is enabled if AWDRE in the AWDCTL Register
is set. If this bit is cleared, the AWD oscillator is disabled and
the watchdog switched off.
Watchdog
The watchdog function is only available in RUN mode. On
setting the AWDRE bit, watchdog functionality in RUN mode
is activated. Once this function is enabled, it is not possible to
disable it via software.
If the timer reaches end value and AWDRE is set, a
system reset is
initiated. Operations of the watchdog function
cease in STOP mode. Normal operation will be continued
when the system is back to RUN mode.
To prevent a watchdog reset, the watchdog timeout
counter must be reset before it reaches the end value. This is
done by a write to the AWDRST bit in the AWDCTL Register.
Autonomous Watchdog Control Register (AWDCTL)
AWDRST — Autonomous Watchdog Reset Bit
This write-only bit resets the Autonomous Watchdog
timeout period. AWDRST always reads 0. Reset clears
AWDRST bit.
1 = Reset AWD and restart timeout period.
0 = No effect.
AWDRE — Autonomous Watchdog Reset Enable Bit
This read / write bit enables resets on AWD time-outs. A
reset on the
RST_A
is asserted when the Autonomous
Watchdog has reached the timeout and the Autonomous
Watchdog is enabled. AWDRE is one-time setable (write
once) after each reset. Reset clears the AWDRE bit.
1 = Autonomous watchdog enabled.
0 = Autonomous watchdog disabled.
AWDR — Autonomous Watchdog Rate Bit
This read / write bit selects the clock rate of the
Autonomous Watchdog. Reset clears the AWDR bit.
1 = Fast rate selected (10 ms).
0 = Slow rate selected (20 ms).
VOLTAGE REGULATOR
The 908E626 chip contains a low-power, low-drop voltage
regulator to provide internal power and external power for the
MCU. The V
DD
regulator accepts a unregulated input supply
and provides a regulated V
DD
supply to all digital sections of
the device. The output of the regulator is also connected to
the VDD terminal to provide the 5.0 V to the microcontroller.
Register Name and Address: AWDCTL - $0a
Bit 7
6
5
4
3
2
1
Bit 0
Read
0
0
0
AWDRE
0
(14)
0
(14)
0
AWDR
Write
AWDRST
Reset
0
0
0
0
0
0
0
0
Notes
16.
This bit must always be set to 0.
相關PDF資料
PDF描述
MMA1200D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1200 Surface Mount Micromachined Accelerometer
MMA1210D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1210 Surface Mount Micromachined Accelerometer
MMA1211D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
相關代理商/技術參數
參數描述
MM908E626AVDWB 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVDWB/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626AVEK 功能描述:馬達/運動/點火控制器和驅動器 QUADSTEPPER W/MCU RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MM908E626AVPEK 功能描述:8位微控制器 -MCU MCU + LIN + MOTOR DRIVER RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626AVPEKR2 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*