- 您現在的位置：買賣IC網 > PDF目錄98023 > ML9205-01GA (OKI ELECTRIC INDUSTRY CO LTD) 24 X 39 DOTS FLUORESCENT DSPL CTRL, PQFP80 PDF資料下載
參數資料
| 型號： | ML9205-01GA |
| 廠商： | OKI ELECTRIC INDUSTRY CO LTD |
| 元件分類： | 顯示控制器 |
| 英文描述： | 24 X 39 DOTS FLUORESCENT DSPL CTRL, PQFP80 |
| 封裝： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件頁數： | 7/34頁 |
| 文件大?。?/td> | 281K |
| 代理商： | ML9205-01GA |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
FEDL9205-03
1Semiconductor
ML9205-01
15/34
Data Transfer Method and Command Write Method
Display control command and data are written by an 8-bit serial transfer.
Write timing is shown in the figure below.
Setting the
CS pin to "Low" level enables a data transfer.
Data is 8 bits and is sequentially input into the DA pin from LSB (LSB first).
As shown in the figure below, data is read by the shift register at the rising edge of the shift clock, which is input
into the
CP pin. If 8-bit data is input, internal load signals are automatically generated and data is written to each
register and RAM.
Therefore it is not necessary to input load signals from the outside.
Setting the
CS pin to "High" disables data transfer. Data input from the point when the CS pin changes from
"High" to "Low" is recognized in 8-bit units.
*
When data is written to RAM (DCRAM, ADRAM, CGRAM) continuously, addresses are internally
incremented automatically.
Therefore it is not necessary to specify the 1st byte to write RAM data for the 2nd and later bytes.
Reset Function
Reset is executed when the
RESET pin is set to "L", (when turning power on, for example) and initializes all
functions.
Initial status is as follows:
Address of each RAM ....................................... address "00"H
Data of each RAM ............................................. All contents are undefined
General output port ............................................ All general output ports go "Low"
Display digit ...................................................... 24 digits
Brightness adjustment........................................ 8/16
All display lights ON or OFF ............................ OFF mode
Segment output .................................................. All segment outputs go "Low"
AD output .......................................................... All AD outputs go "Low"
Please set the functions again according to "Setting Flowchart" after reset.
t
DOFF
B0
LSB
CS
CP
B1 B2 B3 B4 B5 B6 B7
B0 B1 B2 B3 B4 B5 B6 B7
MSB
1st byte
LSB
MSB
2nd byte
Command and address data
t
CSH
B0 B1 B2 B3 B4 B5 B6 B7
LSB
MSB
2nd byte
Character code data of the
next address
Character code data
When data is written
to DCRAM*
DA
相關PDF資料 |
PDF描述 |
|---|---|
| ML9620GAZ210 | 1 CHANNEL(S), 1M bps, LOCAL AREA NETWORK CONTROLLER, PQFP44 |
| MLX90308LUD-CAB | MICROCONTROLLER, UUC |
| MM58167MWC | 0 TIMER(S), REAL TIME CLOCK, UUC24 |
| MM58274CVX | 0 TIMER(S), REAL TIME CLOCK, PQCC20 |
| MM908E621ACDWB/R2 | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO54 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ML9206 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 x 7 Dot Character x 16-Digit Display Controller/Driver with Character RAM |
| ML9206-XX | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 x 7 Dot Character x 16-Digit Display Controller/Driver with Character RAM |
| ML9207 | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character × 24-Digit Display Controller/Driver with Character RAM |
| ML9207-XX | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character × 24-Digit Display Controller/Driver with Character RAM |
| ML9207-XXGA | 制造商:OKI 制造商全稱:OKI electronic componets 功能描述:5 X 7 Dot Character 】 24-Digit Display Controller/Driver with Character RAM |
發布緊急采購，3分鐘左右您將得到回復。