- 您現在的位置：買賣IC網 > PDF目錄25623 > MJ80C32U-25:D (ATMEL CORP) MICROCONTROLLER PDF資料下載
參數資料
| 型號： | MJ80C32U-25:D |
| 廠商： | ATMEL CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MICROCONTROLLER |
| 文件頁數： | 29/109頁 |
| 文件大?。?/td> | 10824K |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
274
7593L–AVR–09/12
AT90USB64/128
7-3 - Reserved
The value read from these bits is always 0. Do not set these bits.
2 - LSM - USB Device Low Speed Mode selection
When configured USB is configured in device mode, this bit allows to select the USB the USB
Low Speed or Full Speed Mod.
Clear to select full speed mode (D+ internal pull-up will be activate with the ATTACH bit will be
set) .
Set to select low speed mode (D- internal pull-up will be activate with the ATTACH bit will be
set). This bit has no effect when the USB interface is configured in HOST mode.
1- RMWKUP - Remote Wake-up bit
Set to send an “upstream-resume” to the host for a remote wake-up (the SUSPI bit must be set).
Cleared by hardware when signalling finished. Clearing by software has no effect.
See Section 23.10, page 266 for more details.
0 - DETACH - Detach bit
Set to physically detach de device (disconnect internal pull-up on D+ or D-).
Clear to reconnect the device. See Section 23.9, page 265 for more details.
7 - Reserved
The value read from this bits is always 0. Do not set this bit.
6 - UPRSMI - Upstream Resume Interrupt flag
Set by hardware when the USB controller is sending a resume signal called “Upstream
Resume”. This triggers an USB interrupt if UPRSME is set.
Shall be cleared by software (USB clocks must be enabled before). Setting by software has no
effect.
5 - EORSMI - End Of Resume Interrupt flag
Set by hardware when the USB controller detects a good “End Of Resume” signal initiated by
the host. This triggers an USB interrupt if EORSME is set.
Shall be cleared by software. Setting by software has no effect.
4 - WAKEUPI - Wake-up CPU Interrupt flag
Set by hardware when the USB controller is re-activated by a filtered non-idle signal from the
lines (not by an upstream resume). This triggers an interrupt if WAKEUPE is set. This interrupt
should be enable only to wake up the CPU core from power down mode.
Shall be cleared by software (USB clock inputs must be enabled before). Setting by software
has no effect.
See Section 23.8, page 265 for more details.
Bit
7
65432
1
0
-
UPRSMI
EORSMI
WAKEUPI
EORSTI
SOFI
-
SUSPI
UDINT
Read/write
Initial value
0
00000
0
相關PDF資料 |
PDF描述 |
|---|---|
| MQ80C32E-36:RD | 8-BIT, 36 MHz, MICROCONTROLLER, CQFP44 |
| S80C32-40:R | 8-BIT, 40 MHz, MICROCONTROLLER, PQCC44 |
| S80C52EXXX-30:D | 8-BIT, MROM, 30 MHz, MICROCONTROLLER, PQCC44 |
| SC80C52XXX-36/883 | 8-BIT, MROM, 36 MHz, MICROCONTROLLER, CDIP40 |
| S83C154TXXX-25 | 8-BIT, MROM, 25 MHz, MICROCONTROLLER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MJ8100 | 制造商:ASI 功能描述:8100 N11E4C |
| MJ8100R | 制造商:SEME-LAB 制造商全稱:Seme LAB 功能描述:Bipolar PNP Device in a Hermetically sealed TO39 |
| MJ-82-1 | 制造商:SPC Multicomp 功能描述:SOCKET PCB DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER 制造商:SPC Multicomp 功能描述:SOCKET, PCB, DC POWER; Gender:Receptacle; Connector Mounting:PCB; Contact Termination:Through Hole Vertical; Connector Mounting Orientation:PCB; Connector Type:Standard Power Entry ;RoHS Compliant: Yes |
| MJ8250FE | 制造商:Ohmite Mfg Co 功能描述: |
| MJ8251F | 制造商:Ohmite Mfg Co 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。