- 您現在的位置：買賣IC網 > PDF目錄383616 > MIC810 (Micrel Semiconductor,Inc.) Microprocessor Reset Circuit(微處理器復位電路（監視基于微處理器系統的電源）) PDF資料下載
參數資料
| 型號： | MIC810 |
| 廠商： | Micrel Semiconductor,Inc. |
| 元件分類： | 復位半導體 |
| 英文描述： | Microprocessor Reset Circuit(微處理器復位電路（監視基于微處理器系統的電源）) |
| 中文描述： | 微處理器復位電路（微處理器復位電路（監視基于微處理器系統的電源）） |
| 文件頁數： | 5/8頁 |
| 文件大?。?/td> | 166K |
| 代理商： | MIC810 |
5
Microprocessor Reset
The RESET pin is asserted whenever VCC falls below
the reset threshold voltage. The reset pin remains
asserted for a period of 240ms after VCC has risen
above the reset threshold voltage. The reset function
ensures the microprocessor is properly reset and powers
up into a known condition after a power failure. RESET
will remain valid with VCCas low as 1.4V.
VCCTransients
The MIC809/MIC810 are relatively immune to negative-
going VCCglitches below the reset threshold. Typically,
a negative-going transient 125mV below the reset
threshold with a duration of 50
μ
s (25
μ
s for
MIC8__R/S/T) or less will not cause an unwanted reset.
Interfacing to Bidirectional Reset Pins
The MIC809/MIC810 can interface with
μ
Ps with
bidirectional reset pins by connecting a 4.7K
resistor in
series with the MIC809/MIC810 output and the
μ
P reset
pin.
RESET Valid to 0V
A resistor can be added from the RESET pin to ground
to ensure the RESET output remains low with VCC
down to 0V. A 100K
resistor connected from RESET
to ground is recommended. The size of the resistor
should be large enough to not load the RESET output
and small enough to pull-down any stray leakage
currents.
Circuit Description
Figure 2. Reset Timing Diagram
Figure 3. RESET Valid to VCC= OV
VCC
Vthr
RESET
t1
t1
Vthr
VCC
RESET
μP
RESET
VCC
MIC809
VCC
100K
MIC809/MIC810 Microprocessor Reset Circuits
相關PDF資料 |
PDF描述 |
|---|---|
| MIC809_U | 20000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
| MIC810_U | 20000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
| MIC8114 | 30000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| MIC8114TU | 30000 SYSTEM GATE LOGIC CELL ARRAY - NOT RECOMMENDED for NEW DESIGN |
| MIC8115 | Microprocessor Reset Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC810_U | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Microprocessor Reset Circuits |
| MIC810JBC3 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Microprocessor Reset Circuits |
| MIC810JU | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Microprocessor Reset Circuits |
| MIC810JU TR | 功能描述:IC RESET GEN 4.63V VTH SOT23-3 RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| MIC810JUY | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Microprocessor Reset Circuits |
發布緊急采購，3分鐘左右您將得到回復。