- 您現在的位置：買賣IC網 > PDF目錄383615 > MIC707 (Micrel Semiconductor,Inc.) μP Supervisory Circuit(μP監控電路（帶電源故障警告和手動復位）) PDF資料下載
參數資料
| 型號： | MIC707 |
| 廠商： | Micrel Semiconductor,Inc. |
| 英文描述： | μP Supervisory Circuit(μP監控電路（帶電源故障警告和手動復位）) |
| 中文描述： | 微處理器監控電路（微處理器監控電路（帶電源故障警告和手動復位）） |
| 文件頁數： | 4/8頁 |
| 文件大小： | 177K |
| 代理商： | MIC707 |
4
Manual Reset Input forces RESET to assert when pulled below 0.8V.
An internal pull-up current of 250
μ
A on this input forces it high when left
floating. This input can also be driven from TTL or CMOS logic.
Primary supply input, +5V.
IC ground pin, 0V reference.
Power fail input. Internally connected to the power fail comparator
which is referenced to 1.25V. The power fail output (PFO) remains
high if PFI is above 1.25V. PFI should be connected to GND or VOUT
if the power fail comparator is not used.
Power fail output. The power fail comparator is independent of all other
functions on this device.
Watchdog input. The WDI input monitors microprocessor activity, an
internal watchdog timer resets itself with each transition on the
watchdog input. If the WDI pin is held high or low for longer than the
watchdog timeout period, WDO is forced to active low. The watchdog
function can be disabled by floating the WDI pin.
No Connect
RESET is asserted if either VCCgoes below the reset threshold or by a
low signal on the manual reset input (MR). RESET remains asserted
for one reset timeout period (200ms) after VCCexceeds the reset
threshold or after the manual reset pin transitions from low to high. The
watchdog timer will not assert RESET unless WDO is connected to
MR.
Output for the watchdog timer. The watchdog timer resets itself with
each transition on the watchdog input. If the WDI pin is held high or
low for longer than the watchdog timeout period, WDO is forced low.
WDO will also be forced low if VCCis below the reset threshold and
will remain low until VCCreturns to a valid level.
RESET is the compliment of RESET and is asserted if either VCCgoes
below the reset threshold or by a low signal on the manual reset input
(MR). RESET is suitable for microprocessors systems that use an
active high reset.
Pin No.
MIC705
MIC706
MIC707
MIC708
Pin Name
MR
1
1
VCC
2
2
GND
3
3
PFI
4
4
PFO
5
5
WDI
6
N/A
N/C
N/A
6
RESET
7
7
WDO
8
N/A
RESET
N/A
8
Pin Functions
MIC705/6/7/8
μ
P Supervisory Circuits
相關PDF資料 |
PDF描述 |
|---|---|
| MIC706S | μP Supervisory Circuit(μP監控電路（帶看門狗定時器，微處理器復位，電源故障警告和手動復位功能）) |
| MIC706P | 40000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
| MIC70__M | レP Supervisory Circuits |
| MIC70__N | 40000 SYSTEM GATE 3.3 VOLT LOGIC CELL AR - NOT RECOMMENDED for NEW DESIGN |
| MIC708T | μP Supervisory Circuit(μP監控電路（帶電源故障警告和手動復位）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC707M | 功能描述:IC SUPERVISOR 4.65V VTH 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| MIC707M TR | 功能描述:IC SUPERVISOR 4.65V VTH 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
| MIC707MY | 功能描述:監控電路 P Supervisor, Watchdog Timer, SOIC-08 (Lead Free) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MIC707MY TR | 功能描述:監控電路 P Supervisor, Watchdog Timer, SOIC-08 (Lead Free) RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| MIC707N | 功能描述:IC SUPERVISOR 4.65V VTH 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 監控器 系列:- 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:低有效 復位超時:標準傳輸延遲為 60 µs 電壓 - 閥值:3V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:Digi-Reel® 其它名稱:LM8364BALMF30DKR |
發布緊急采購，3分鐘左右您將得到回復。