- 您現在的位置：買賣IC網 > PDF目錄383614 > MIC5268-1.2BM5 (MICREL INC) 150mA UCap CMOS LDO Regulator w/Power Good PDF資料下載
參數資料
| 型號： | MIC5268-1.2BM5 |
| 廠商： | MICREL INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 150mA UCap CMOS LDO Regulator w/Power Good |
| 中文描述： | 1.2 V FIXED POSITIVE LDO REGULATOR, PDSO5 |
| 封裝： | SOT-23, 5 PIN |
| 文件頁數： | 6/9頁 |
| 文件大?。?/td> | 55K |
| 代理商： | MIC5268-1.2BM5 |
MIC5268
Applications Information
Enable/Shutdown
The MIC5268 comes with an active-high enable pin that
allows the regulator to be disabled. Forcing the enable pin low
disables the regulator and sends it into a
“
zero
”
off-mode-
current state. In this state, current consumed by the regulator
goes nearly to zero. Forcing the enable pin high enables the
output voltage. This part is CMOS and the enable pin cannot
be left floating; a floating enable pin may cause an indetermi-
nate state on the output.
Input Capacitor
An input capacitor is not required for stability. A 1
μ
F input
capacitor is recommended when the bulk ac supply capaci-
tance is more than 10 inches away from the device, or when
the supply is a battery.
Output Capacitor
The MIC5268 requires an output capacitor for stability. The
design requires 1
μ
F or greater on the output to maintain
stability. The capacitor can be a low-ESR ceramic chip
capacitor. The MIC5268 has been designed to work specifi-
cally with the low-cost, small chip capacitors. Tantalum
capacitors can also be used for improved capacitance over
temperature. The value of the capacitor can be increased
without bound.
X7R dielectric ceramic capacitors are recommended be-
cause of their temperature performance. X7R-type capaci-
tors change capacitance by 15% over their operating tem-
perature range and are the most stable type of ceramic
capacitors. Z5U and Y5V dielectric capacitors change value
by as much 50% and 60% respectively over their operating
temperature ranges. To use a ceramic chip capacitor with
Y5V dielectric, the value must be much higher than an X7R
ceramic or a tantalum capacitor to ensure the same minimum
capacitance value over the operating temperature range.
Tantalum capacitors have a very stable dielectric (10% over
their operating temperature range) and can also be used with
this device.
Power Good
The power good output is an open-drain output. It is designed
essentially to work as a power-on reset generator once the
regulated voltage was up and/or a fault condition. The output
of the power good drives low when a fault condition AND an
undervoltage detection occurs. The power good output comes
back up once the output has reached 97% of its nominal value
and a 1ms to 5ms delay has passed. See Timing Diagram
The MIC5268
’
s internal circuit intelligently monitors
overcurrent, overtemperature and dropout conditions and
ORs thes outputs together ti indicate some fault condition.
this output is fed into an on-board delay circuitry that drives
the open drain transistor to indicate a fault.
Micrel
MIC5268
6
September 2002
Transient Response
The MIC5268 implements a unique output stage to dramati-
cally improve transient response recovery time. The output is
a totem-pole configuration with a P-channel MOSFET pass
device and an N-channel MOSFET clamp. The N-channel
clamp is a significantly smaller device that prevents the
output voltage from overshooting when a heavy load is
removed. This feature helps to speed up the transient re-
sponse by significantly decreasing transient response recov-
ery time during the transition from heavy load (100mA) to light
load (100
μ
A).
Active Shutdown
The MIC5268 also features an active shutdown clamp, which
is an N-channel MOSFET that turns on when the device is
disabled. This allows the output capacitor and load to dis-
charge, de-energizing the load.
Thermal Considerations
The MIC5268 is designed to provide 150mA of continuous
current in a very small package. Maximum power dissipation
can be calculated based on the output current and the voltage
drop across the part. To determine the maximum power
dissipation of the package, use the junction-to-ambient ther-
mal resistance of the device and the following basic equation:
P
T
T
D(max)
J(max)
A
JA
=
θ
T
J(max)
is the maximum junction temperature of the die,
125
°
C, and T
A
is the ambient operating temperature.
θ
JA
is
layout dependent; Table 1 shows examples of junction-to-
ambient thermal resistance for the MIC5268.
Package
θ
JA
Recommended
Minimum Footprint
θ
JA
1" Square
Copper Clad
θ
JC
SOT-23-5 (M5)
235
°
C/W
185
°
C/W
145
°
C/W
Table 1. SOT-23-5 Thermal Resistance
The actual power dissipation of the regulator circuit can be
determined using the equation:
P
D
= (V
IN
–
V
OUT
) I
OUT
+ V
IN
I
GND
Substituting P
D(max)
for P
D
and solving for the operating
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit. For
example, when operating the MIC5268-1.2BM5 at 50
°
C with
a minimum footprint layout, the maximum input voltage for a
set output current can be determined as follows:
P
125 C
235 C/W
5
C
D(max)
=
°
0
P
D(max)
= 315mW
The junction-to-ambient thermal resistance for the minimum
footprint is 235
°
C/W, from Table 1. The maximum power
dissipation must not be exceeded for proper operation. Using
the output voltage of 1.2V and an output current of 150mA,
the maximum input voltage can be determined. Because this
device is CMOS and the ground current is typically 100
μ
A
over the load range, the power dissipation contributed by the
相關PDF資料 |
PDF描述 |
|---|---|
| MIC5319 | 500mA ?Cap Ultra-Low Dropout, High PSRR LDO Regulator |
| MIC5319-2 | 500mA ?Cap Ultra-Low Dropout, High PSRR LDO Regulator |
| MIC5319-8BD5 | 500mA ?Cap Ultra-Low Dropout, High PSRR LDO Regulator |
| MIC5319-8BML | 500mA ?Cap Ultra-Low Dropout, High PSRR LDO Regulator |
| MIC5319-8YD5 | 500mA ?Cap Ultra-Low Dropout, High PSRR LDO Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC5270-3.0BM5 TR | 功能描述:IC REG LDO -3V .1A SOT23-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:500 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:12V 輸入電壓:14.5 V ~ 35 V 電壓 - 壓降（標準）:- 穩壓器數量:1 電流 - 輸出:500mA 電流 - 限制（最小）:- 工作溫度:-40°C ~ 125°C 安裝類型:通孔 封裝/外殼:TO-205AD，TO-39-3 金屬罐 供應商設備封裝:TO-39 包裝:散裝 其它名稱:*LM78M12CH*LM78M12CH/NOPBLM78M12CH |
| MIC5270-3.0YM5 | 制造商:Micrel Inc 功能描述:IC REG LDO 100MA -3.0V SOT23-5*NIC* |
| MIC5270-3.0YM5 TR | 功能描述:低壓差穩壓器 - LDO 100mA Negative uCap LDO Regulator(Lead Free) RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC5270-3.0YM5TR | 制造商:Micrel 功能描述:LDO Regulator Neg -3V 0.1A |
| MIC5270-3.0YM5-TR | 功能描述:Linear Voltage Regulator IC Negative Fixed 1 Output -3V 100mA SOT-23-5 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 穩壓器拓?fù)?負，固定式 電壓 - 輸出:-3V 電流 - 輸出:100mA 電壓 - 跌落（典型值）:0.5V @ 100mA 穩壓器數:1 電壓 - 輸入:可下調至-16V 電流 - 限制（最小值）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商器件封裝:SOT-23-5 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。