- 您現在的位置：買賣IC網 > PDF目錄383613 > MIC5159BM6 (MICREL INC) PROGRAMMABLE CURRENT LIMIT UCAP LDO REGULATOR CONTROLLER PDF資料下載
參數資料
| 型號： | MIC5159BM6 |
| 廠商： | MICREL INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | PROGRAMMABLE CURRENT LIMIT UCAP LDO REGULATOR CONTROLLER |
| 中文描述： | SPECIALTY ANALOG CIRCUIT, PDSO6 |
| 封裝： | SOT-23, 6 PIN |
| 文件頁數： | 8/23頁 |
| 文件大小： | 400K |
| 代理商： | MIC5159BM6 |
MIC5159
Micrel
M9999-041204
8
April 2004
The typical thermal resistance from the junction to the case
(
θ
JC
) of a TO-263 (D
2
pack) is 6
°
C/W. Adding 0.2
°
C/W for
case to sink thermal resistance (
θ
CS
), the heatsink must have
a sink to ambient thermal resistance (
θ
SA
) of:
θ
SA
=
θ
JA
–
(
θ
JC
+
θ
CS
)
θ
SA
= 25.71
°
C/W
–
(6
°
C/W + 0.2
°
C/W)
θ
SA
= 19.51
°
C/W
According to the calculations, the heatsink must have a
θ
SA
of 19.51
°
C/W or better.
For a full discussion of heat sinking and thermal effects on
voltage regulators, refer to the
“
Regulator Thermals
”
section
of Micrel
’
s Designing with Low-Dropout Voltage Regulators
handbook.
Short-Circuit Current Limit
The above thermal design calculations apply to normal
operation. In the case where the P-Channel MOSFET must
survive extended periods of short-circuit current, another
approach for thermal design must be considered. Due to the
fact that the MIC5159 delivers constant current limiting,
power dissipated by the MOSFET is equal to the input voltage
multiplied by the maximum output current.
Figure 1 shows a simple, inexpensive circuit that allows the
current limiting to be re-entrant. This reduces power dissipa-
tion in current limited conditions. As the output voltage begins
to drop, the differential voltage across the input and output
increases. This pulls the current sense voltage lower, reduc-
ing the amount of output current to maintain 50mV across the
sense resistor. This reduction in output current equates to a
reduction in power dissipation in the MOSFET. Figures 2 and
3 show a comparison of linear current limiting versus the re-
entrant current limiting scheme implemented in Figure 1.
MIC5159-1.8BM6
R
VOUT
1k
W
R
25m
W
C1
10μF
3.3 V
IN
R
VIN
10
W
Q1,2,3
Si4433DYx3
ISENSE
VIN
GATE
VOUT
C2
47μF
1.8 V
OUT
1.5A
Figure 1. Re-Entrant Current Limit
0
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
0
0
0
0
1
1
1
1
O
OUTPUT CURRENT (A)
Constant Current Limit
Re-Entrant
Current Limit
Figure 2. Output Voltage Characteristics
Re-Entrant Current Limit
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
0
0.5
1
1.5
P
OUTPUT VOLTAGE (V)
Re-Entrant
Current Limiting
Constant Current
Limiting
Figure 3. Power Dissipation
vs. Output Voltage
Enable/Shutdown
The MIC5159 comes with an active-high enable pin that
allows the regulator to be disabled. Forcing the enable pin low
disables the regulator and sends it into a low off-mode-
current state. Forcing the enable pin high enables the output
voltage. This part is CMOS and the enable pin cannot be left
floating; a floating enable pin may cause an indeterminate
state on the output.
Output Capacitor
The MIC5159 requires an output capacitor to maintain stabil-
ity and improve transient response. Proper selection is impor-
tant to ensure proper operation. The MIC5159 output capaci-
tor selection is highly dependent upon the components and
the application. With a very high gate charge (gate capaci-
tance) MOSFET, the output requires a much larger valued
ceramic capacitor for stability. As an alternative to a large
valued ceramic capacitor, a smaller-valued tantalum capaci-
tor can be used to provide stability. At higher load currents,
lower R
DS(ON)
MOSFETs are used; these MOSFETs typi-
cally having much larger gate charge. If the application does
not require ultra-low-dropout voltage, smaller values of ce-
ramic capacitance may be used.
Input Capacitor
An input capacitor of 1.0
μ
F or greater is recommended when
the device is more than 4 inches away from the bulk AC
supply capacitance or when the supply is a battery. Small,
surface mount, ceramic capacitors can be used for bypassing
the input to the regulator, further improving the integrity of the
output voltage. Larger input capacitors may be required
depending on the impedance of the source and the output
load requirements.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC5190 | ECONOLINE: RY & RX - Controllable Output- 1kVDC Isolation- No Heatsink Required- UL94V-0 Package Material- Toroidal Magnetics- No External Components- Fully Encapsulated- Efficiency to 70% |
| MIC5191 | Ultra High-Speed, High-Current Active Filter/LDO Controller |
| MIC5191BML | Ultra High-Speed, High-Current Active Filter/LDO Controller |
| MIC5191BMM | Ultra High-Speed, High-Current Active Filter/LDO Controller |
| mic5204 | SCSI-II Active Terminator(兼容SCSI-II的有效終端) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC5159BM6 TR | 功能描述:IC REG CTRLR SGL POS ADJ SOT23-6 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性晶體管驅動器 系列:- 產品培訓模塊:More Information on LDOs 標準包裝:2,500 系列:- 類型:正，固定式 輸出數:2 輸出電壓:2.8V，3.3V 電流 - 電源:12mA 輸入電壓:5 V ~ 22 V 工作溫度:0°C ~ 70°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| MIC5159YM6 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:Programmable Current Limit μCap LDO Regulator Controller |
| MIC5159YM6 TR | 功能描述:低壓差控制器 - LDO Progr. Ilim LDO Controller(Lead Free) RoHS:否 制造商:Micrel 最大輸入電壓:5.5 V 輸出電壓:Adjustable 輸出電流:10 mA 負載調節: 輸出類型:Adjustable, Fixed 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-6 |
| MIC5159YM6TR | 制造商:Micrel 功能描述:LDO Regulator 1.235V to 5.5V |
| MIC5159YM6-TR | 功能描述:Linear Regulator Controller IC Positive Adjustable 1 Output SOT-23-6 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:正，可調式 輸出數:1 電流 - 電源:10mA 電壓 - 輸入:1.65 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。