- 您現在的位置：買賣IC網 > PDF目錄384736 > MIC5014BN (MICREL INC) FPGA 1000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN PDF資料下載
參數資料
| 型號： | MIC5014BN |
| 廠商： | MICREL INC |
| 元件分類： | 功率晶體管 |
| 英文描述： | FPGA 1000000 SYSTEM GATE 1.8 VOLT - NOT RECOMMENDED for NEW DESIGN |
| 中文描述： | BUF OR INV BASED MOSFET DRIVER, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 76K |
| 代理商： | MIC5014BN |
MIC5014/5015
Micrel
MIC5014/5015
6
1997
the short is removed, feedback to the input pin insures that the
MIC5014 will turn back on. This output can also be level
shifted and sent to an I/O port of a microcontroller for intelli-
gent control.
Current Shunts
(R
S
). Low valued resistors are necessary for
use at R
S
. Resistors are available with values ranging from 1
to 50m
, at 2 to 10W. If a precise overcurrent trip point is
not necessary, then a nonprecision resistor or even a mea-
sured PCB trace can serve as R
S
. The major cause of drift in
resistor values with such resistors is temperature coefficient;
the designer should be aware that a linear, 500 ppm/
°
C
change will contribute as much as 10% shift in the overcurrent
trip point. If this is not acceptable, a power resistor designed
for current shunt service (drifts less than 100 ppm/
°
C), or a
Kelvin-sensed resistor may be used.
Suppliers of Precision Power Resistors:
Dale Electronics, Inc., 2064 12th Ave., Columbus, NE 68601. (402) 565-
3131
International Resistive Co., P.O. Box 1860, Boone,NC 28607-1860.
(704) 264-8861
Isotek Corp., 566 Wilbur Ave. Swansea, MA 02777. (508) 673-2900
Kelvin, 14724 Ventura Blvd., Ste. 1003, Sherman Oaks, CA 91403-3501.
(818) 990-1192
RCD Components, Inc., 520 E. Industrial Pk. Dr., Manchester, NH 03103.
(603) 669-0054
Ultronix, Inc., P.O. Box 1090, Grand Junction, CO 81502 (303) 242-0810
High Side Driver With Delayed Current Sense
(Figure 5)
Delay of the overcurrent detection to accomodate high inrush
loads such as incandescent or halogen lamps can be accom-
plished by adding an LM3905 timer as a one shot to provide
an open collector pulldown for the comparator output such
that the control input of the MIC5015 stays low for a preset
amount of time without interference from the current sense
circuitry. Note that an MIC5015 must be used in this applica-
tion (figure 5), as an inverting control input is necessary. The
delay time is set by the RC time constant of the external
components on pins 3 and 4 of the timer; in this case, 6ms was
chosen.
An LM3905 timer was used instead of a 555 as it provides a
clean transition, and is almost impossible to make oscillate.
Good bypassing and noise immunity is essential in this circuit
to prevent spurious op amp oscillations.
Low Side Driver
(Figure 2) A key advantage of this topology,
as previously mentioned, is speed. The MOSFET gate is
driven to near supply immediately when the MIC5014/15 is
turned on. Typical circuits reach full enhancement in 50
μ
s or
less with a 15V supply.
Bootstrapped High Side Driver (Figure 3) The turn-on time of
a high side driver can be improved to faster than 40
μ
s by
bootstrapping the supply with the MOSFET source. The
Schottky barrier diode prevents the supply pin from dropping
more than 200mV below the drain supply and improves turn-
on time. Since the supply current in the
“
off
”
state is only a
small leakage, the 100nF bypass capacitor tends to remain
charged for several seconds after the MIC5014/15 is turned
off. Faster speeds can be obtained at the expense of supply
voltage (the overvoltage shutdown will turn the part off when
the bootstrapping action pulls the supply pin above 35V) by
using a larger capacitor at the junction of the two 1N4001
diodes. In a PWM application (this circuit can be used for either
PWM
’
ed or continuously energized loads), the chip supply is
sustained at a higher potential than the system supply, which
improves switching time.
Figure 3. Bootstrapped Hgh-Side Driver
High Side Driver With Current Sense (Figure 4) Although no
current sense function is included on the MIC5014/15 devices,
a simple current sense function can be realized via the addition
of one more active component; an LM301A op amp used as
a comparator. The positive rail of the op amp is tied to V
+
, and
the negative rail is tied to ground. This op amp was chosen as
it can withstand having input transients that swing below the
negative rail, and has common mode range almost to the
positive rail.
The inverting side of this comparator is tied to a voltage divider
which sets the voltage to V
+
–
V
TRIP
. The non inverting side
is tied to the node between the drain of the FET and the sense
resistor. If the overcurrent trip point is not exceeded , this node
will always be pulled above V
+
–
V
TRIP
, and
the output of the
comparator will be high which feeds the control input of the
MIC5014 (polarities should be reversed if the MIC5015 is
used). One the overcurrent trip point has been reached, the
comparator will go low, which shuts off the MIC5014. When the
L
MIC5014
1
2
3
4
8
7
6
5
NC
Gate
Gnd
Source
Input
V+
NC
NC
10μF
R4
1k
R
S
0.06
12V
On
R1
1k
R2
120k
LM301A
2.2k
I
= V
/R
S
= 1.7A
V
TRIP
= R1/(R1+R2)
L
MIC5015
V+
Control Input
ON
OFF
1
2
3
4
8
7
6
5
+2.75V to +30V
NC
Gate
Gnd
Source
Input
NC
NC
1μF
100nF
1N4001 (2)
1N5817
1RF540
Figure 4. High Side Driver with Overcurrent Shutdown
相關PDF資料 |
PDF描述 |
|---|---|
| MIC5015BM | Low-Cost High- or Low-Side MOSFET Driver Final Information |
| MIC5015BN | Low-Cost High- or Low-Side MOSFET Driver Final Information |
| MIC5014 | Low-Cost High- or Low-Side MOSFET Driver(低成本 高/低邊MOS場效應管驅動器) |
| MIC5015 | Low-Cost High- or Low-Side MOSFET Driver(低成本 高/低邊MOS場效應管驅動器) |
| MIC502 | FPGA - 100000 SYSTEM GATE 2.5 VOLT - NOT RECOMMENDED for NEW DESIGN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC5014YM | 功能描述:功率驅動器IC Low Cost High Side MOSFET Predriver - Lead Free RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MIC5014YM TR | 功能描述:功率驅動器IC Low Cost High Side MOSFET Predriver - Lead Free RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MIC5014YM | 制造商:Micrel Inc 功能描述:MOSFET Driver IC |
| MIC5014YMTR | 制造商:Micrel 功能描述:MOSFET Driver 1-Out Hi/Lo Side Non-Inv |
| MIC5014YM-TR | 功能描述:IC DRIVER MOSF HI/LO SIDE 8SOIC 制造商:microchip technology 系列:- 包裝:剪切帶（CT） 零件狀態:有效 驅動配置:高壓側或低壓側 通道類型:單路 驅動器數:1 柵極類型:N 溝道 MOSFET 電壓 - 電源:2.75 V ~ 30 V 邏輯電壓?- VIL，VIH:0.8V，2V 電流 - 峰值輸出（灌入，拉出）:- 輸入類型:非反相 高壓側電壓 - 最大值（自舉）:- 上升/下降時間（典型值）:- 工作溫度:-40°C ~ 150°C（TJ） 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。