- 您現在的位置：買賣IC網 > PDF目錄384736 > MIC49200-1.8WR (MICREL INC) 2A LOW VOLTAGE LDO WITH DUAL INPUT VOLTAGES PDF資料下載
參數資料
| 型號： | MIC49200-1.8WR |
| 廠商： | MICREL INC |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | 2A LOW VOLTAGE LDO WITH DUAL INPUT VOLTAGES |
| 中文描述： | 1.8 V FIXED POSITIVE LDO REGULATOR, 0.625 V DROPOUT, PSSO5 |
| 封裝： | ROHS COMPLIANT, S-5 |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 333K |
| 代理商： | MIC49200-1.8WR |
Micrel, Inc.
MIC49200
Applications Information
The MIC49200 is an ultra-high performance, low-
dropout linear regulator designed for high current
applications requiring fast transient response. The
MIC49200 utilizes two input supplies, signi
fi
cantly
reducing dropout voltage, perfect for low-voltage, DC-
to-DC conversion. The MIC49200 requires a minimum
of external components and obtains a bandwidth of up
to 10MHz. As a μCap regulator, the output is tolerant
of virtually any type of capacitor including ceramic
type and tantalum type capacitors.
January 2006
10
M9999-011306
(408) 955-1690
The MIC49200 regulator is fully protected from
damage due to fault conditions, offering linear current
limiting and thermal shutdown.
Bias Supply Voltage
V
BIAS
, requiring relatively light current, provides power
to the control portion of the MIC49200. V
BIAS
requires
approximately 40mA for a 1.5A load current. Dropout
conditions require higher currents. Most of the biasing
current is used to supply the base current to the pass
transistor. This allows the pass element to be driven
into saturation thereby reducing the dropout to 400mV
at a 2A load current. Bypassing on the bias pin is
recommended to improve performance of the
regulator during line and load transients. Small
ceramic capacitors from V
BIAS
-to-ground help reduce
high-frequency noise from being injected into the
control circuitry from the bias rail and represent good
design practice. Good bypass techniques typically
include one larger capacitor such as 1μF ceramic and
smaller valued capacitors such as 0.01μF or 0.001μF
in parallel with that larger capacitor to decouple the
bias supply. The V
BIAS
input voltage must be 2.1V
above the output voltage with a minimum V
BIAS
input
voltage of 3 volts.
Input Supply Voltage
V
IN
provides the high current to the collector of the
pass transistor. The minimum input voltage is 1.4V,
allowing conversion from low voltage supplies.
Output Capacitor
The MIC49200 requires a minimum of output
capacitance to maintain stability. However, proper
capacitor selection is important to ensure desired
transient response. The MIC49200 is speci
fi
cally
designed to be stable with virtually any capacitance
value and ESR. A 1μF ceramic chip capacitor should
satisfy most applications. Output capacitance can be
increased without bound. See “
Typical Characteristic
”
subsection for examples of load transient response.
X7R dielectric ceramic capacitors are recommended
because of their temperature performance. X7R-type
capacitors change capacitance by 15% over their
operating temperature range and are the most stable
type of ceramic capacitors. Z5U and Y5V dielectric
capacitors change value by as much as 50% and 60%
respectively over their operating temperature ranges.
To use a ceramic chip capacitor with Y5V dielectric,
the value must be much higher than an X7R ceramic
or a tantalum capacitor to ensure the same
capacitance value over the operating temperature
range. Tantalum capacitors have a very stable
dielectric (10% over their operating temperature
range) and can also be used with this device.
Input Capacitor
An input capacitor of 1μF or greater is recommended
when the device is more than 4" away from the bulk
supply capacitance, or when the supply is a battery.
Small, surface-mount, ceramic chip capacitors can be
used for the bypassing. The capacitor should be
placed within 1" of the device for optimal performance.
Larger values will help to improve ripple rejection by
bypassing the input to the regulator, further improving
the integrity of the output voltage.
Thermal Design
Linear regulators are simple to use. The most
complicated design parameters to consider are
thermal characteristics. Thermal design requires the
following application-speci
fi
c parameters:
Maximum ambient temperature (T
A
)
Output current (I
OUT
)
Output voltage (V
OUT
)
Input voltage (V
IN
)
Ground current (I
GND
)
First, calculate the power dissipation of the regulator
from these numbers and the device parameters from
this datasheet.
P
D
= V
IN
× I
IN
+ V
BIAS
× I
BIAS
– V
OUT
× I
OUT
As the load increases, the input current will be less
than the output current at high output currents. The
bias current is a sum of base drive and ground
current. Ground current is constant over load current.
The heat sink thermal resistance is determined with
this formula:
D
A
J(MAX)
T
SA
P
T
θ
=
相關PDF資料 |
PDF描述 |
|---|---|
| MIC49200 | 2A LOW VOLTAGE LDO WITH DUAL INPUT VOLTAGES |
| MIC49200-1.0WR | 2A LOW VOLTAGE LDO WITH DUAL INPUT VOLTAGES |
| MIC49200WR | 2A LOW VOLTAGE LDO WITH DUAL INPUT VOLTAGES |
| MIC5011 | Minimum Parts High- or Low-Side MOSFET Driver(高/低邊MOS場效應管驅動器) |
| MIC5011BM | Minimum Parts High- or Low-Side MOSFET Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MIC49200WR | 功能描述:低壓差穩壓器 - LDO 2A LDO, Low Vin, Low Vout, Fast transient response, ucap stable RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC49200WR TR | 功能描述:低壓差穩壓器 - LDO 2A LDO, Low Vin, Low Vout, Fast transient response, ucap stable RoHS:否 制造商:Texas Instruments 最大輸入電壓:36 V 輸出電壓:1.4 V to 20.5 V 回動電壓（最大值）:307 mV 輸出電流:1 A 負載調節:0.3 % 輸出端數量: 輸出類型:Fixed 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-20 |
| MIC49300 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.0A LOW VOLTAGE LDO REGULATOR W/DUAL INPUT VOLTAGES |
| MIC49300_05 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:3.0A Low Voltage LDO Regulator w/Dual Input Voltages |
| MIC49300-0.9BR | 功能描述:IC REG LDO 0.9V 3A SPAK-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:3,000 系列:- 穩壓器拓?fù)浣Y(jié)構:正，固定式 輸出電壓:3.8V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.3V @ 80mA 穩壓器數量:1 電流 - 輸出:80mA 電流 - 限制（最?。?- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:帶卷 (TR) 其它名稱:MIC5203-3.8BM5TRMIC5203-3.8BM5TR-ND |
發布緊急采購，3分鐘左右您將得到回復。